TFA MODUS PLUS 35.1122 Instrucciones De Uso página 10

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 28
TFA_No. 35.1122_Anl.
07.09.2012
MODUS PLUS – Wireless weather station
• There are 3 different reception symbols:
- reception is active
- reception is very good
- No DCF reception
• To activate the DCF reception, press the ALARM button for 2 seconds. The
reception signal - symbol flashes. Press the ALARM button again to stop
scanning DCF time signal.
• If the clock cannot detect the DCF-signal (for example due to disturbances,
transmitting distance, etc.), the clock can be set manually.
• The clock will then work as a normal quartz clock. (see: Manual setting of
the clock, calendar and day-of-week language).
Note for radio-controlled time DCF:
The time base for the radio-controlled time is a caesium atomic clock operat-
ed by the Physikalisch Technische Bundesanstalt Braunschweig. It has a time
deviation of less than one second in one million years. The time is coded and
transmitted from Mainflingen near Frankfurt via frequency signal DCF-77
(77.5 kHz) and has a transmitting range of approximately 1,500 km. Your
radio controlled clock receives this signal, converts it to shows the precise
time. Changeover from summer time or winter time are automatic. The quali-
ty of the reception depends mainly on the geographic location. Normally
there should be no reception problems within a 1,500 km radius around
Frankfurt.
Please take note of the following:
• Recommended distance to any interfering sources like computer moni-
tors or TV sets is at least 1.5 - 2 metres.
• Inside ferro-concrete rooms (basements, superstructures), the received
signal is naturally weakened. In extreme cases, please place the unit close
to a window to improve the reception.
• During nighttime, the atmospheric interference is usually less severe and
reception is possible in most cases. A single daily reception is adequate to
keep the accuracy deviation below 1 second.
7. Operation
• During the reception of the outdoor values or the time is a button opera-
tion not possible.
• In the setting mode, press ▼/UNIT or ▲/CH button to select the values.
Press and hold the buttons for fast running.
• The instrument will automatically quit the setting mode if no button is
pressed within 10 seconds.
• Each button operation is acknowledged with a beep.
18
14:18 Uhr
Seite 10
MODUS PLUS – Wireless weather station
7.1 Manual setting of the clock, calendar and day-of-week language
• Press the MODE/ENTER button for 2 seconds in normal mode to enter the
setting mode.
• 24 Hr starts flashing.
• Press the ▲/CH or ▼/UNIT button to choose 12 HR (PM appears on the dis-
play after 12h) or 24 HR system.
• Confirm with the MODE/ENTER button.
• The setting sequence is shown as follows: Hours, minutes, year, month/
day sequence (American version) or day/month (European version),
month, date, the language for the weekday. Press the ▼/UNIT or ▲/CH
button to adjust it.
• Day-of-week language: English (E), German (G), French (F), Spanish (S)
and Italian (I).
• Press the MODE/ENTER button again to return to normal mode.
• When the DCF reception is activated, the manually set clock will be over-
written by a successfully reception of the DCF time.
7.2 Recall of time, weekday, alarm time and date
• Press the MODE/ENTER button in normal mode to change the display
between:
→ Time with seconds
→ Time with weekday
→ 1. Alarm time
→ 2. Alarm time
→ Date
7.3 Setting of the alarm
• Press the MODE/ENTER button in normal mode, until the flashing 1 for
the first alarm time appears.
• 0:00 or the last adjusted alarm time appears.
• You can now adjust the first alarm time.
• Press and hold MODE/ENTER button.
• The hour digit is flashing. Press the ▲/CH or ▼/UNIT button to adjust
hours.
• The alarm symbol appears on the display.
• Press the MODE/ENTER button again and you can adjust the minutes with
the ▼/UNIT or ▲/CH button.
• Confirm the settings with the MODE/ENTER button.
• The alarm for the first alarm time is activated.
• Press the MODE/ENTER button again.
• 2 for the second alarm time is flashing.
• 0:00 or the last adjusted alarm time appears.
• Set the alarm time for the second alarm in the same way.
19

Publicidad

Tabla de contenido
loading

Tabla de contenido