Noise Information; Vibration Information - Worx WG384E Manual Del Usuario

NOISE INFORMATION

A weighted sound pressure
A weighted sound power
Wear ear protection.

VIBRATION INFORMATION

Vibration total values (triax vector sum) determined
according to EN 60745:
Vibration emission value
a = xxm/s
2
h
The declared vibration total value may be used for
comparing one tool with another, and may also be
used in a preliminary assessment of exposure.
WARNING: The vibration emission value
during actual use of the power tool can differ
from the declared value depending on the ways in
which the tool is used dependant on the following
examples and other variations on how the tool is
used:
How the tool is used and the materials being cut or
drilled.
The tool being in good condition and well maintained.
Using the correct accessory for the tool and ensuring
16
it is sharp and in good condition.
The tightness of the grip on the handles and if any
anti vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may significantly reduce the exposure level
over the total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these
instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti
vibration accessories.
Plan your work schedule to spread any high vibration
tool use across a number of days.
Cordless Chain Saw
L = XX dB(A)
pA
K = XX dB(A)
PA
L = XX dB(A)
wA
K = XX dB(A)
PA
Uncertainty K = 1.5m/s²
INTENDED USE
The chain saw is intended for sawing of trees, tree
trunks, branches, wooden beams, planks, etc. Cuts
can be sawed with or across the grain. This product is
not suitable for sawing mineral materials.
ASSEMBLY
WARNING! Do not install the battery pack
before it has been completely assembled.
Always use gloves when handling the chain.
CHAIN AND GUIDE BAR ASSEMBLY
1. Unpack all parts carefully. Remove the chain cover
by turning the chain tensioning knob in a counter-
clockwise direction. (See Fig. A1)
2. Place the chain saw on a solid, level surface.
3. Use only genuine WORX chains or those
recommended for Guide Bar.
4. Slide the chain in the slot around the guide bar.
Ensure the chain is in correct running direction by
comparing it to the chain icon on the guide bar, or
referring to the chain direction symbol found on
the saw body. Ensure the bar tensioning plate is
facing outward. (See Fig. A2)
5. Fit the chain onto the drive sprocket, so that the
fastening bar hole and the two bar locating tabs
on the bar pad fit into the keyway of the opening
on the guide bar. (See Fig. B1, B2)
6. Assure all parts are seated properly and hold chain
and guide bar in a level position. Make sure the
drive links are fully seated in the drive sprocket
(See Fig. C1), avoiding a kink as shown in Fig. C2.
If kink occurs, pick up on the chain at the guide bar
just ahead of the kink and then pull the kink out.
NOTE: Chain should rotate freely and be free of
kinks.
7. Fit the chain cover and tighten the chain cover by
turning the chain tensioning knob clockwise until it
is tight. (See Fig. D)
8. The chain will stretch while cutting and lose
proper tension. When the chain becomes loose,
completely unscrew the chain tensioning knob
or turn the knob around three (3) full turns in a
counter-clockwise direction, then retighten the
chain tensioning knob to properly reset the chain
tension by repeating Steps 6-7 listed above.
WARNING: The chain is not yet
tensioned. Tensioning the chain applies
as described under "TENSIONING
CHAIN". The chain now needs to be inspected
to make sure it is properly tensioned.
TENSIONING CHAIN (See Fig. E1, E2)
NOTE: New saw chains will stretch. Check the chain
tension frequently when first used and tighten when
the chain becomes loose around the guide bar.
WARNING:
● Removing the battery pack before adjusting saw
chain tension.
EN