Noise Information; Vibration Information - Worx WG322E Manual Original

NOISE INFORMATION

WG322E.1
WG322E.9
A weighted sound
L = 87.9 dB(A)
pressure
pA
A weighted sound
L = 96 dB(A)
power
wA
K =3.0 dB(A)
PA
Wear ear protection

VIBRATION INFORMATION

Vibration total values (triax vector sum) determined ac-
cording to EN 60745:
Vibration emission value
a < 2.5 m/s 2
h
The declared vibration total value may be used for
comparing one tool with another, and may also be used in a
preliminary assessment of exposure.
WARNING: The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which the
tool is used dependant on the following examples and
other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained.
Using the correct accessory for the tool and ensuring it is
sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration accessories are used.
And the tool is being used as intended by its design and
these instructions.
This tool may cause hand-arm vibration syndrome if
its use is not adequately managed
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the
operating cycle such as the times when the tool is switched
off and when it is running idle but not actually doing the job.
This may significantly reduce the exposure level over the
total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and
keep well lubricated (where appropriate).
If the tool is to be used regularly then invest in anti vibration
accessories.
Plan your work schedule to spread any high vibration tool
use across a number of days.
Cordless Chain Saw
WG322E
WG323E
WG323E.9
L = 85.7 dB(A)
pA
L = 96 dB(A)
wA
Uncertainty K = 1.5 m/s2
INTENDED USE
The chain saw is intended for sawing of trees, tree trunks,
branches, wooden beams, planks, etc. Cuts can be sawed
with or across the grain. This product is not suitable for
sawing mineral materials .
ASSEMBLY
WARNING! Do not install the battery pack
before it has been completely assembled.
Always use gloves when handling the chain.
CHAIN AND GUIDE BAR ASSEMBLY
1. Unpack all parts carefully.
2. Place the chain saw on a solid, level surface.
3. Use only genuine Worx chains or those recommended
for Guide Bar.
4. Slide the Chain (7) in the slot around the Guide Bar
(6). Ensure the Chain is in correct running direction
by comparing it to the chain icon on the guide bar, or
referring to the Chain Direction Symbol (17) found on
the saw body. Ensure the Bar Tensioning Plate (24) is
facing outward. (See Fig. A)
5. Fit the Chain onto the Drive Sprocket (16), so that the
Fastening Bar hole (20) and the two Bar Locating
Tabs (21) on the Bar Pad (19) fit into the keyway of the
opening on the Guide Bar (6). (See Fig. B1, B2)
6. Assure all parts are seated properly. Make sure the drive
links are fully seated in the drive sprocket (See Fig. C1),
avoiding a kink as shown in Fig. C2. If kink occurs, pick
up on the chain at the guide bar just ahead of the kink
and then pull the kink out.
NOTE: Chain should rotate freely and be free of kinks.
7. Fit the Chain Cover (9) and tighten the Chain Cover by
turning the Chain Tensioning Knob (8) clockwise until it
is tight. (See Fig. D)
WARNING: The chain is not yet tensioned.
Tensioning the chain applies as described
under "TENSIONING CHAIN". The chain now
needs to be inspected to make sure it is properly
tensioned.
TENSIONING CHAIN (See Fig. E1, E2)
NOTE: New saw chains will stretch. Check the chain tension
frequently when first used and tighten when the Chain (7)
becomes loose around the Guide Bar (6).
WARNING:
● Removing the battery pack before adjusting saw chain
tension.
● Cutting edges on chain are sharp. Use protective gloves
when handling chain.
● Maintain proper chain tension always. A loose chain will
increase the risk of kickback. A loose chain may jump
out of guide bar groove. This may injure operator and
damage chain. A loose chain will cause chain, bar, and
sprocket to wear rapidly.
1. Place the chain saw on any suitable flat surface.
2. Turn the Chain Tensioning Knob (8) clockwise until it is
hand tight.
17
EN