Functional Description; Removing/Inserting The Battery - Milwaukee M18 Manual Del Operador

Ocultar thumbs Ver también para M18:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

FUNCTIONAL DESCRIPTION

4
3
2
1. Trigger
2. LED
3. Keyless chuck
4. Torque selector collar
5. Application selector collar
(2607-20 only)
6. Side handle
(not included)
7. Speed selector
8. Control switch
9. Handle
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always use a side
handle when using a 9.0 Ah or higher capac-
ity battery pack with this tool. Always brace or
hold securely. Ensure side handle is tightened
securely before each use.
6
7
5
1
Installing the Side Handle
If your drill/driver did not come with a side handle,
visit www.milwaukeetool.com for the appropriate
accessory handle.
1. To install the side handle, loosen
the side handle grip until the
hooks are far enough apart to fit
into the slots on the gear case
ring. Position the side handle on
the top, pointing to the left or
right. Tighten the side handle grip
until it is secure.
2. To remove the side handle,
loosen the side handle grip until
the side handle can be removed. Reposition and
tighten securely.
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
8
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Always remove battery pack before changing
9
or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Always remove the battery before inserting or remov-
ing bits. Select the proper style and size bit for the job.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction. When using drill bits,
allow the bit to strike the bottom of the chuck.
Center the bit in the chuck jaws and lift it about
1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the counter-
clockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem with
the chuck's operation.
Selecting Drill or Drive Action
1. To use the drilling mode, rotate the
torque selector collar until the drill
symbol
appears in line with the
arrow.
2. To use the driving mode rotate
the torque selector collar until the
desired clutch setting appears in
line with the arrow.
The adjustable clutch, when prop-
erly adjusted, will slip at a preset
torque to prevent driving the screw
too deep into different materials
and to prevent damage to the
screw or tool.
4
OPERATION
To reduce the risk of injury, always
Installing Bits
(Cat. No. 2606-20)
Hooks
Slots

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

2606-202607-20

Tabla de contenido