Main Components; Assembly; Assembly Components; Grass Catcher Assembly - Stiga MP1 500 Li D48 Serie Manual De Instrucciones

Ocultar thumbs Ver también para MP1 500 Li D48 Serie:
Tabla de contenido

Publicidad

3.4

MAIN COMPONENTS

The machine is composed of a series of main
components that have the following functions (Fig.1.0):
A.
Chassis: this is the casing that houses
the rotating cutting means.
B.
The engine: drives both the cutting means
and the wheel traction (if available).
C.
Cutting means: the element
designed to cut the grass.
D.
Rear discharge guard: it is a safety device which
prevents objects collected by the cutting means
from being projected away from the machine.
Side discharge guard (if available): it
E.
is a safety device which prevents objects
collected by the cutting means from being
projected away from the machine.
F.
Side discharge chute (if available): apart from
discharging the grass on the ground laterally,
it also constitutes a safety element, preventing
any objects collected by the cutting means from
being projected away from the machine.
G.
Grass catcher: apart from collecting the
mown grass, the grass catcher also constitutes
a safety element, preventing any objects
collected by the cutting means from being
projected away from the machine.
H.
Handle: this is the operator's work station.
It is long enough to ensure the operator
remains at a safe distance from the rotary
cutting means whilst working.
I.
Battery (if it is not supplied with the machine,
see chapter 15 "attachments on request"):
provides the energy for starting the motor;
its specifications and regulations for use
are described in a specific manual.
J.
Operator presence lever: this lever enables
the cutting means and drive to be operated. The
motor stops when both levers are released.
K.
Drive engagement lever: this lever engages the drive
to the wheels and allows the machine to move forward.
L.
Hatch for accessing the battery compartment
M.
Safety key (Deactivation device): The key
enables / disables the machine electric circuit.
N.
Battery charger (if it is not supplied with the
machine, see chapter 15 "attachments on
request"): device used to recharge the battery.
4.

ASSEMBLY

The safety regulations to follow are described in
chap. 2. Strictly comply with these instructions to avoid
serious risks or dangers.
For storage and transport purposes, some components of
the machine are not installed in the factory and have to be
assembled after unpacking. Follow the instructions below.
Unpacking and completing the assembly should
be done on a flat and stable surface, with enough
space for moving the machine and its packaging,
always making use of suitable equipment. Do not use
the machine until all the instructions provided in the
"ASSEMBLY" section have been carried out.
4.1

ASSEMBLY COMPONENTS

The packaging includes assembly components.
4.1.1
Unpacking
1.
Carefully open the packaging, paying
attention not to lose components.
2.
Consult the documentation in the box,
including these instructions.
3.
Remove all the unassembled parts from the box.
4.
Dispose of the box and packaging in
compliance with local regulations.
Before assembling, make sure the safety key is
not inserted into its housing.
4.2

GRASS CATCHER ASSEMBLY

Follow the instructions provided in the instructions
sheet accompanying the grass catcher.
4.3

HANDLE ASSEMBLY

Assemble the handle according to the
indications in (Fig.3) (Fig.7).
5.

CONTROLS

5.1

SAFETY KEY (DEACTIVATION DEVICE)

The key (Fig.8.A) is located inside
the battery compartment.
Turning the key to "ON", the electric circuit of the
machine is activated, thus starting the machine.
Turning the key to "OFF", the electric circuit of the
machine is completely deactivated, to prevent
any uncontrolled use of the machine.
IMPORTANT Remove the safety key whenever
the machine is unused or left unattended.
5.2

OPERATOR PRESENCE LEVER

The operator presence lever (Fig.9.A) enables
the cutting means and drive engagement.
Press one of the two levers (Fig.9.A) against the handle to
enable the cutting means and drive engagement functions.
When both levers are released, the motor
automatically stops and all functions are disabled.
EN - 5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mp1 550 li d48 serie

Tabla de contenido