Manuales relacionados para Sanus VMT5
Resumen de contenidos para Sanus VMT5
- Página 1 VMT 5 INSTRUCTION MANUAL We’ll Make It Stress-Free If you have any questions along the way, just give us a call. 1-800-359-5520. We’re ready to help! Scan for easy install video http://san.us/405...
- Página 2 Does your TV weigh more than 75 lb (34 kg) including accessories? No — Perfect! 75 lb (34 kg) Yes — This mount is NOT compatible. Visit MountFinder.Sanus.com or call 1-800-359-5520 (UK: 0800-056-2853) to fi nd a compatible mount. What is your wall made of? Drywall with Solid concrete or...
- Página 3 STEP 1 Attach Bracket to TV Parts and Hardware for STEP 1 WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer;...
- Página 4 1-1 Select TV Screws 1-2 Spacers Hand thread screws into the threaded inserts on the back of your TV Spacers and screws are supplied to install your TV bracket. to determine which screw diameter (M4, M5, M6, or M8) to use. Determine your preference for spacer configuration when attaching your TV bracket.
- Página 5 1-3 Attach TV Brackets Center the TV brackets over your TV hole pattern as shown - making sure the brackets are level. NOTE: The adjustment knobs on TV brackets should be oriented to the outside edges. Install using the spacer, screw and washer combination you selected for your TV. Spacer, screw and washer Adjustment Knob...
- Página 6 13 cm (5 in.) between your device and the magnet. Please consult with your physician or medical professional prior to using this product. NOTE: Not all hardware included will be used. Sanus Magnetic Stud Finder * Wall Plate *...
- Página 7 Finder* located in your Welcome folder for more detailed operation of stud finder. Min. 406 mm (16 in.) Locate a nail/screw in the studs using the Sanus magnetic stud finder provided. Find the edges of the studs using the probe of the stud finder Mark the centers of the studs with pencil.
- Página 8 Level the wall plate template and tape in place. NOTE: For assistance in determining wall plate location, see HeightFinder at sanus.com. IMPORTANT : Be sure you mark and drill into the center of the stud.
- Página 9 Partially install the top two lag bolts , leaving about 13 mm (1/2 in.) space from the wall. NOTE: This space allows you to remove the wall plate template and hang the wall plate onto the top lag bolts Remove the wall plate template ≈...
- Página 10 Slide the covers open on the wall plate to expose the mounting holes. Hang the wall plate on the top lag bolts Cover Cover...
- Página 11 10. Install the bottom two lag bolts . Tighten all four lag bolts only until they are pulled firmly against the wall plate NOTE: Hold the wall plate in place when tightening the first lag bolt to keep the plate from shifting out of place. CAUTION: Improper use could reduce the holding power of the lag bolt .
- Página 12 NOTE: See Introducing Sanus Magnetic Stud Finder* located in your Welcome folder for more detailed operation of stud finder. Locate a nail/screw in the stud using the Sanus magnetic stud finder provided. Find the edges of the stud using the probe of the stud finder Mark the center of the stud with pencil.
- Página 13 Level the wall plate template and tape in place. NOTE: For assistance in determining wall plate location, see HeightFinder at sanus.com. IMPORTANT : Be sure you mark and drill into the center of the stud.
- Página 14 Remove the wall plate template and insert two anchors into the outer top holes. CAUTION: Be sure the anchors are seated flush with the drywall surface. Partially install the top two lag bolts into the anchors , leaving about 13 mm (1/2 in.) space from the wall. NOTE: This space allows you to hang the wall plate onto the top lag bolts ≈...
- Página 15 Slide the covers open on the wall plate to expose the mounting holes. Hang the wall plate on the top lag bolts Cover Cover...
- Página 16 10. Install the middle two lag bolts . Tighten all four lag bolts only until they are pulled firmly against the wall plate NOTE: Hold the wall plate in place when tightening the first lag bolt to keep the plate from shifting out of place. CAUTION: Improper use could reduce the holding power of the lag bolt .
- Página 17 Level the wall plate template and mark the hole locations. NOTE: For assistance in determining wall plate location, see Height Finder at sanus.com. Drill four pilot holes using a 10 mm (3/8 in.) diameter drill bit.
- Página 18 Remove the wall plate template and insert four anchors CAUTION: Be sure the anchors are seated flush with the concrete surface. Partially install the top two lag bolts , leaving about 13 mm (1/2 in.) space from the wall. NOTE: This space allows you to hang the wall plate onto the top lag bolts ≈...
- Página 19 Slide the covers open on the wall plate to expose the mounting holes. Hang the wall plate on the top lag bolts Cover Cover...
- Página 20 Install the bottom two lag bolts . Tighten all four lag bolts only until they are pulled firmly against the wall plate NOTE: Hold the wall plate in place when tightening the first lag bolt to keep the wall plate from shifting out of place. CAUTION: Improper use could reduce the holding power of the lag bolt .
- Página 21 STEP 3 Attach TV to Wall Plate HEAVY ! You may need assistance with this step. Hook the TV/brackets onto the wall plate NOTE: The TV/brackets can be slid anywhere along the wall plate for optimal positioning of your TV. Rest the TV into place against the wall.
- Página 22 Manage Cables Tilt the TV up or down to gain access to the back of the TV. Attach your cables, then adjust the TV as desired. Cables...
- Página 23 Adjustments LEVEL Tilt To level your TV, turn the level adjustment screw on the top of Your TV should adjust easily when moved, then stay in place. either TV bracket to raise or lower that respective Adjust the tilt tension knob if your TV naturally tilts up or down. side of the TV.
- Página 24 TV LATERAL SHIFT REMOVING THE TV HEAVY ! You may need HEAVY ! You may need assistance with this step. assistance with this step. Disconnect all cables from the TV. Slide the TV left or right along the To unlock the TV from the wall plate: pull both release cords down and toward the TV wall plate to reposition.
- Página 25 Features TV tilts up or down for the Brackets adjust side to TV bracket expands perfect viewing angle side within the wall plate to fi t TV hole patterns for optimal positioning from 200 x 200 mm up to 400 x 400 mm Locking mechanisms Adjustment knobs allow Level adjustments create...
- Página 26 Dimensions 23.25 590.6 16.00 [mm] 406.4 7.25 5.08 184.2 128.9 0.35 0.72 18.3 15.75 2.14 400.0 54.3 7.87 7.00° 200.0 7.87 200.0 17.70 449.6 15.75 400.0 12.00°...
-
Página 28: Listo Para Comenzar
¿Su televisor pesa más de 34 kg (75 lb), incluidos los accesorios? No — ¡Perfecto! 34 kg Sí — Este soporte NO es compatible. Visite MountFinder.Sanus.com o llame al 1-800-359-5520 (Reino Unido: 0800-056-2853) para (75 lb) encontrar un soporte compatible. -
Página 29: Paso 1 Colocar Las Placas De Sujeción En El Televisor
ESPAÑOL PASO 1 Colocar las placas de sujeción en el televisor Ver página 3 Piezas y elementos de sujeción para el PASO 1 ADVERTENCIA: Este producto contiene piezas pequeñas que, si fuesen tragadas, podrían producir asfixia. Antes de iniciar el ensamblaje, compruebe que todas las piezas estén incluidas y en buenas condiciones. Si faltan piezas o alguna está dañada, no devuelva el artículo al distribuidor;... -
Página 30: Opción Para Montantes De Madera (Instalación De Doble Montante)
Se deben verificar las partes centrales de los pernos, no todas las paredes tienen una separación convencional de 406 mm (16") NOTA: Consulte la sección Presentación del detector magnético de bordes de montantes Sanus* que se encuentra en su carpeta de bienvenida para obtener más detalles sobre el funcionamiento del detector de bordes de montantes. -
Página 31: Opción Para Montantes De Madera (Instalación De Un Solo Montante)
Se debe verificar la parte central NOTA: Consulte la sección Presentación del detector magnético de bordes de montantes Sanus* que se encuentra en su carpeta de bienvenida para obtener más detalles sobre el funcionamiento del detector de bordes de montantes. - Página 32 Nivele la plantilla de la placa mural y fíjela con cinta adhesiva en el lugar. NOTA: Si necesita ayuda para determinar la ubicación de la placa mural, utilice la herramienta HeightFinder disponible en sanus.com. IMPORTANTE : Asegúrese de marcar y perforar el centro del montante.
-
Página 33: Opción Para Hormigón Sólido O Bloques De Cemento
Nivele la plantilla de la placa mural y marque la ubicación de los orificios. NOTA: Si necesita ayuda para determinar la ubicación de la placa mural, utilice la herramienta HeightFinder disponible en sanus.com. Haga los cuatro orificios guía con una mecha de 10 mm (3/8") de diámetro. -
Página 34: Paso 3 Fijar El Televisor A La Placa Mural
ESPAÑOL PASO 3 Fijar el televisor a la placa mural Ver página 21 ¡ELEMENTO PESADO ! Es posible que necesite ayuda en este paso. Cuelgue el módulo televisor-placas en la placa mural NOTA: El módulo televisor-placas se pueden deslizar hacia cualquier parte junto con la placa mural para lograr un posicionamiento óptimo de su televisor. -
Página 35: Descripción
ESPAÑOL DESPLAZADOR LATERAL DEL TELEVISOR ¡ELEMENTO PESADO ! Es posible que necesite ayuda en este paso. Deslice el televisor hacia la izquierda o hacia la derecha junto con la placa mural para cambiar su posición. EXTRACCIÓN DEL TELEVISOR ¡ELEMENTO PESADO ! Es posible que necesite ayuda en este paso. - Página 36 ©2013 Milestone AV Technologies, a Duchossois Group Company. All rights reserved. Sanus is a division of Milestone. All other brand names or marks are used for identifi cation purposes and are trademarks of their respective owners.