Maintenance - Panasonic SC-PM600 Instrucciones De Funcionamiento

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Main unit displays
--:--"
"
• You connected the AC mains lead for the first time or there
was a power failure recently. Set the clock.
"
ADJUST CLOCK"
• The clock is not set. Adjust the clock.
ADJUST TIMER"
"
• The play timer is not set. Adjust the play timer.
AUTO OFF"
"
• The system has not been used for 20 minutes and will
switch off within a minute. To cancel, press any button.
ERROR"
"
• An incorrect operation was done. Read the instructions and
try again.
F61"
"
F77"
"
• Disconnect the AC mains lead and consult your dealer.
F703"
"
®
• Examine the Bluetooth
connection.
• Disconnect the Bluetooth
and then switch on again.
"
F76"
• There is a problem with the power supply.
• Disconnect the AC mains lead and consult your dealer.
NODEVICE"
"
• The USB device is not connected. Examine the connection.
NO DISC"
"
• You have not put in a disc.
NO PLAY"
"
• Examine the content. You can only play supported format.
• The system may have a problem. Switch off the system and
then switch on again.
PLAYERROR"
"
• You played an unsupported MP3 file. The system will skip
that track and play the next one.
REMOTE 1"
"
REMOTE 2"
"
• The remote control and the main unit are using different
codes. Change the code of the remote control.
– When "REMOTE 1" is shown, press and hold [OK] and
[ ] for a minimum of 4 seconds.
– When "REMOTE 2" is shown, press and hold [OK] and
[USB/CD] for a minimum of 4 seconds.
SOUND 1 NOT SET"
"
SOUND 2 NOT SET"
"
SOUND 3 NOT SET"
"
• You have not saved the sound effects into the sound
setting number.
USB OVER CURRENT ERROR"
"
• The USB device is using too much power. Disconnect the
USB device, switch off the system and then switch on
again.
VBR"
"
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
®
device. Switch off the system
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [USB/CD] to select "CD".
To set the code to "REMOTE 2"
1
Press and hold [CD] on the main unit and [USB/CD]
on the remote control.
"REMOTE 2" is shown.
2
Press and hold [OK] and [USB/CD] for a minimum of
4 seconds.
To set the code to "REMOTE 1"
1
Press and hold [CD] on the main unit and [ ] on the
remote control.
"REMOTE 1" is shown.
2
Press and hold [OK] and [ ] for a minimum of
4 seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC mains lead.
2
While you press and hold [1] on the main unit,
connect the AC mains lead again.
Continue to press and hold the button until
"– – – – – – – – –" is shown.
3
Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.

Maintenance

To clean this system, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this
system.
• Before using chemically treated cloth, read the
instructions that came with the cloth carefully.
11
11

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido