Troubleshooting - Fellowes Metal 100r Manual De Instrucciones

ENGLISH
BINDING A DOCUMENT
1 2
MÁX 20
(80gsm)
Punch front and back covers Punch sheets in small batches
first. so as not to overload the
machine or the user.
5 6
Hold the document in both hands, Use the binding pliers to cut and
with the metal coil on the right fold the end of the metal coil. Clip
side. Touch the metal coil against off the excess coil.
the inserting roller to bind the
document.
CORRECTING A BOUND DOCUMENT
Additional sheets may be included or removed at any time by first removing the old metal coil. Correct document as necessary, then rebind as
described.
REMOVAL OF WASTE CLIPPINGS
The waste tray is located in the back of the machine. For best results empty the tray regularly.
13
Metal100R_409587_RevB_3L_041317.indd 13-14
3 4
Switch the inserting roller on. Collate the document. Load the
coil on to the first 3 holes.
7 8
Turn the document around. Clip off the excess coil.

TROUBLESHOOTING

Problem Cause
Punched holes are not central Edge guide not set
Machine will not punch Blockage
Punch holes are not parallel to Debris are stuck below dies.
edge.
Sheets not correctly aligned to punch
Partial holes
pattern.
Damaged hole edges Possibly overloading the machine
WORLDWIDE WARRANTY
Fellowes warrants all parts of the binder to be free of defects in material
and workmanship for 2 years from the date of purchase by the original
consumer. If any part is found to be defective during warranty period,
your sole and exclusive remedy will be repair or replacement, at
Fellowes' option and expense, of the defective part. This warranty does
not apply in cases of abuse, mishandling or unauthorised repair. Any im-
plied warranty, including that of merchantability or fitness for particular
purpose, is hereby limited in duration to the appropriate warranty period
W.E.E.E.
Español
Se clasifica este producto como Equipamiento Eléctrico y Electrónico. Si llegase el momento de deshacerse de este producto, asegúrese que lo hace
cumpliendo la Directiva Europea sobre Residuos de Equipamiento Eléctrico y Electrónico (Waste of Electrical and Electronic Equipment, WEEE) y las leyes
locales relacionadas con esta directiva.
Para más información acerca de la Directiva WEEE, visite www.fellowesinternational.com/WEEE
Português
Este produto está classificado como Equipamento Eléctrico e Electrónico. Quando chegar a altura de eliminar este produto, certifique-se de que o faz
em conformidade com a Directiva relativa a Resíduos de Equipamentos Eléctricos e Electrónicos (REEE) e em observância da legislação local relativa a
esta directiva.
Para obter mais informações sobre a Directiva relativa a Resíduos de Equipamentos Eléctricos e Electrónicos (REEE), visite o endereço www.
fellowesinternational.com/WEEE
English
This product is classified as Electrical and Electronic Equipment. Should the time come for you to dispose of this product please ensure that you do so in
accordance with the European Waste of Electrical and Electronic Equipment (WEEE) Directive and in compliance with local laws relating to this directive.
For more information on the WEEE Directive please visit www.fellowesinternational.com/WEEE
Solution
Adjust edge guide until hole pattern is correct
Check waste tray is empty. Check for blockage to paper
entry
Take stiff cardboard and slide into the paper entry. Move
the cardboard sideways to release any stray clippings into
the waste tray
Adjust edge guide and test punch scrap sheets until correct
Punch plastic covers with paper sheets. Reduce number of
sheets being punched
set forth above. In no event shall Fellowes be liable for any consequential
damages attributable to this product. This warranty gives you specific le-
gal rights. You may have other legal rights that vary from this warranty.
The duration, terms and conditions of this warranty are valid worldwide,
except where different limitations, restrictions or conditions may be
required by local law. For more details or to obtain services under this
warranty, please contact Fellowes or your dealer.
14
4/13/17 3:04 PM