Maintenance; General; Carburetor Adjustment; Checking, Maintaining And Servicing Chain Saw Safety Equipment - Husqvarna 440e II TrioBrake Manual De Instrucciones

Ocultar thumbs Ver también para 440e II TrioBrake:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

General

The user must only carry out the maintenance and
service work described in this manual. More extensive
work must be carried out by an authorized service
workshop.

Carburetor adjustment

Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions.
Function
The carburetor governs the engine's speed via the
throttle control. Air and fuel are mixed in the
carburetor. The air/fuel mixture is adjustable. Correct
adjustment is essential to get the best performance
from the machine.
The T-screw regulates the throttle setting at idle
speed. If the T-screw is turned clockwise this gives a
higher idle speed; turning it anti-clockwise gives a
lower idle speed.
Basic settings and running in
The basic carburetor settings are adjusted during testing
at the factory. Fine adjustment should be carried out by a
skilled technician.
Rec. idle speed: See the Technical data section.
Fine adjustment of the idling speed T
Adjust the idle speed with the T-screw. If it is necessary to
re-adjust, turn the T-screw clockwise while the engine is
running, until the chain starts to rotate. Then turn counter-
clockwise until the chain stops. A correctly adjusted idle
speed setting occurs when the engine runs smoothly in
every position. It should also be good margin to the rpm
when the chain starts to rotate.
WARNING! Contact your servicing
!
dealer, if the idle speed setting cannot be
adjusted so that the chain stops at idle.
Do not use the chain saw until it has
been properly adjusted or repaired.
Correctly adjusted carburetor
When the carburetor is correctly adjusted the machine
accelerates without hesitation and the machine 4-cycles a
little at max. speed. It is also important that the chain does
not rotate at idle. If the L-jet is set too lean it may cause
starting difficulties and poor acceleration. If the H-jet is set
too lean the machine will have less power, poor
acceleration and could suffer damage to the engine.
26 – English

MAINTENANCE

Checking, maintaining and
servicing chain saw safety
equipment
Note! All servicing and repair work on the machine
requires special training. This is especially true of the
machine's safety equipment. If your machine fails any of
the checks described below we recommend you to
contact our servicing dealer.
Chain brake and front hand guard
Checking brake band wear
Brush off any wood dust, resin and dirt from the chain
brake and clutch drum. Dirt and wear can impair operation
of the brake. (97)
Regularly check that the brake band is at least 0.024 inch
(0,6 mm) thick at its thinnest point.
Checking the front hand guard
Make sure the front hand guard is not damaged and that
there are no visible defects such as cracks.
Move the front hand guard forwards and back to make
sure it moves freely and that it is securely anchored to the
clutch cover.
Checking the inertia brake release
With the engine turned off, hold the chain saw over a
stump or other firm object. Let go of the front handle so
that the bar drops towards the stump as the chain saw
rotates around the rear handle. (98)
When the bar hits the stump the brake should be
activated. (99)
Checking the right-hand brake trigger
Check that the right hand guard is not damaged and that
there are no visible defects, such as cracks. (27)
Push the trigger up and forwards to check that it moves
freely and is securely hinged to the clutch cover. (28)
Never carry or hang the saw by the trigger! This could
damage the mechanism and disable the chain brake.
(29)
Checking the brake trigger
Place the chain saw on firm ground and start it. Make sure
the chain does not touch the ground or any other object.
See the instructions under the heading Start and stop.
(100)
1155361-49 Rev.3 2017-05-03

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

445e ii triobrake

Tabla de contenido