Bosch GDS 250-LI Professional Manual Original página 13

(11) Application tool (e.g. impact socket)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Cordless impact screw-
driver
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard
screwdriving application ac-
cording to ISO 5393
Machine screw diameter
Tool holder
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
B)
– during operation and
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
C) only for inductive batteries
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-2.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 102.0 dB(A); sound power level
113.0 dB(A). Uncertainty K = 3.0 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Tightening screws and nuts of the maximum permitted size:
2 2
a <14.5 m/s , K=1.5 m/s ,
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
Bosch Power Tools
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
GDS 250-LI
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
3 601 JG6 1..
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
V = 18
over the total working period.
rpm 0–2 400
Implement additional safety measures to protect the oper-
rpm 0–3 300
ator from the effects of vibration, such as servicing the
Nm 250 power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
mm M10–M18
∎ ½"
u
A)
kg 1.9–2.0
°C 0... +45
°C –20... +50
Battery charging
Note: The battery is supplied partially charged. To ensure
GBA 18 V...
full battery capacity, fully charge the battery in the charger
GBA 18 V...W
before using your power tool for the first time.
AL 1820 CV
The lithium-ion battery can be charged at any time without
AL 1860 CV
reducing its service life. Interrupting the charging process
GAL 1880 CV
does not damage the battery.
GAL 3680 CV
The lithium-ion battery is protected against deep discharge
GAL 18V-..
by the "Electronic Cell Protection (ECP)". When the battery
C)
GAL 18.. W
is discharged, the power tool is switched off by means of a
GAX 18V-30
protective circuit: The application tool no longer rotates.
u
Removing the battery
The battery is equipped with two locking levels to prevent
the battery from falling out when pushing the battery release
button unintentionally. As long as the battery is inserted in
the power tool, it is held in position by means of a spring.
To remove the battery , press the release button and pull the
battery forward and out of the power tool. Do not use force
to do this.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
1 609 92A 4VZ | (07.12.2018)
English | 13