ION Vinyl Motion Air Guia De Inicio Rapido página 8

Troubleshooting
If you experience any difficulties, please refer to the troubleshooting steps below as well as those in
the EZ Vinyl/Tape Converter manual included with this product.
If you are recording to a computer:
• Make sure that Vinyl Motion Air is powered on and that the needle is on the record.
• Make sure Vinyl Motion Air is selected as your computer's default recording device (see the instructions
below).
• If you are listening through your computer's speakers, make sure those speakers are selected as your
computer's default playback device (see the instructions below). Alternatively, you could connect Vinyl Motion
Air's RCA outputs to a stereo system or powered speakers. Do not connect them to phono-level inputs; Vinyl
Motion Air's RCA outputs are line-level and could damage a device with phono-level inputs.
(Note: The RCA outputs monitor the signal coming out of the turntable, not the signal coming from your
computer.)
• Disconnect then reconnect the USB cable connecting Vinyl Motion Air to your computer.
I'm not hearing any audio when playing music:
• If you are playing music from vinyl:
o Make sure that Vinyl Motion Air is powered on and that the needle is on the record.
o Connect Vinyl Motion Air's RCA outputs to a stereo system or powered speakers. (Do not connect them
to phono-level inputs; Vinyl Motion Air's RCA outputs are line-level and could damage a device with
phono-level inputs.)
• If you are playing music from your computer:
o Make sure your software music player's volume is turned up.
o Make sure your computer's volume is turned up.
o Make sure your computer's speakers are selected as your computer's default playback device (see the
instructions below). (Vinyl Motion Air cannot be used as a playback device for your computer's audio.)
I am hearing a hum through my speaker or laptop when using the turntable:
• If you are recording to a laptop:
o Please connect the laptop to a grounded power supply (3 prong)
• If you are playing through a speaker:
o Please connect to a grounded (3 prong) power supply.
My record is not playing at the correct speed; its pitch is too high or too low:
• Ensure the 33 / 45 / 78 switch is set to the correct speed for your record.
The Bluetooth speaker that I want is not pairing to Vinyl Motion Air.
• Turn off or move other nearby Bluetooth speakers over 30' (9.1m) so only the closest Bluetooth speaker you
want will pair.
I am connected to a Bluetooth speaker but do not hear any audio.
• If you are connected to a Bluetooth speaker with a play/pause button, and do not hear audio, try pressing the
play/pause button.
• Press and release Vinyl Motion Air's Bluetooth button to disconnect it from the Bluetooth speaker, and then
press it once more to try pairing it again.
• Turn Vinyl Motion Air off and then on again, and then press its Bluetooth button to try pairing it again.
• Use the volume knob on Vinyl Motion Air to turn up the Bluetooth output level.
My smartphone will not connect to Vinyl Motion Air Turntable.
• Vinyl Motion Air Turntable acts as a Bluetooth Transmitter, sending the audio out of Vinyl Motion Air into other
Bluetooth Speakers. Vinyl Motion Air Turntable cannot act as a Bluetooth Receiver and play music from your
smartphone over headphones or RCA outputs.
The Bluetooth LED will not stop blinking.
• Once the Bluetooth button is pressed, Vinyl Motion Air will try to connect to nearby Bluetooth speakers for 5
minutes. To stop the blinking Bluetooth LED, power cycle Vinyl Motion Air.
I am hearing an echo when listening to music.
• Either listen to music through a paired Bluetooth speaker or connect the RCA audio outputs from Vinyl Motion
Air to a speaker. Both playback methods should not be used at the same time.
I am hearing static noise in my headphones.
• Press Vinyl Motion Air's Bluetooth button to disconnect it from a paired Bluetooth speaker. When listening to
Vinyl Motion Air with headphones, always make sure Vinyl Motion Air is not connected to a Bluetooth speaker
at the same time.
8