Ce - Declaration - WAGNER FINISH CONTROL 3500 Manual De Instrucciones

FinishControl 3500
3. Handling
If defects can be seen in the materials, processing or perform-
ance of the device during the guarantee period, guarantee
claims must be made immediately, or at the latest within a
period of 2 weeks.
The authorised specialist shop that delivered the device is enti-
tled to accept guarantee claims. Guarantee claims may also be
made to the service centres named in our operating instruc-
tions. The product has to be sent without charge or presented
together with the original purchase document that includes
details of the purchase date and the name of the product. In
order to claim for an extension to the guarantee, the guaran-
tee certificate must be included.
The costs as well as the risk of loss or damage to the product
in transit or by the centre that accepts the guarantee claims
or who delivers the repaired product, are the responsibility of
the customer.
4. Exclusion of guarantee
Guarantee claims cannot be considered
-
for parts that are subject to wear and tear due to use or other
natural wear and tear, as well as defects in the product that
are a result of natural wear and tear, or wear and tear due
to use. This includes in particular cables, valves, packaging,
jets, cylinders, pistons, means-carrying housing components,
filters, pipes, seals, rotors, stators, etc. Damage due to wear and
tear that is caused in particular by sanded coating materials,
such as dispersions, plaster, putty, adhesives, glazes, quartz
foundation.
-
in the event of errors in devices that are due to non-compliance
with the operating instructions, unsuitable or unprofessional
use, incorrect assembly and/or commissioning by the buyer
or by a third party, or utilisation other than is intended,
abnormal ambient conditions, unsuitable coating materials,
unsuitable operating conditions, operation with the incorrect
mains voltage supply/frequency, over-operation or defective
servicing or care and/or cleaning.
-
for errors in the device that have been caused by using
accessory parts, additional components or spare parts that
are not original Wagner parts.
-
for products to which modifications or additions have been
carried out.
-
for products where the serial number has been removed or
is illegible
-
for products to which attempts at repairs have been carried
out by unauthorised persons.
-
for products with slight deviations from the target properties,
which are negligible with regard to the value and usability of
the device.
-
for products that have been partially or fully taken apart.
5. Additional regulations.
The above guarantees apply exclusively to products that have
been bought by authorised specialist shops in the EU, CIS,
Australia and are used within the reference country.
If the check shows that the case is not a guarantee case, re-
pairs are carried out at the expense of the buyer.
The above regulations manage the legal relationship to us
concludingly. Additional claims, in particular for damages and
losses of any type, which occur as a result of the product or
its use, are excluded from the product liability act except with
regard to the area of application.
Claims for liability for defects to the specialist trader remain
unaffected.
German law applies to this guarantee. The contractual lan-
guage is German. In the event that the meaning of the Ger-
man and a foreign text of this guarantee deviate from one an-
other, the meaning of the German text has priority.
J. Wagner GmbH
Division Professional Finishing
Otto Lilienthal Strasse 18
88677 Markdorf
Federal Republic of Germany
EU Declaration of conformity
We declare under sole responsibility that this product
conforms to the following relevant stipulations:
2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU
Applied harmonised norms:
EN 60745-1, EN 50580, EN 62233, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3
The EU declaration of conformity is enclosed with the
product.
If required, it can be re-ordered using order number
2368396.
GB
GUARANTEE DECLARATION
Subject to modifications
27