EINHELL TC-SM 2131/1 Dual Manual De Instrucciones Original página 47

•
Retighten the locking screw (14) to secure the
turntable in place.
•
Adjust the miter angle on the machine head
and the stop rail as described under points
5.5 and 5.6.
•
Cut as described under section 6.1.
6.5 Limiting the cutting depth (Fig. 15)
•
The cutting depth can be infinitely adjusted
using the screw (27). Turn the screw (27) in or
out to set the required cutting depth and then
retighten the knurled nut on the screw (27).
•
Check the setting by completing a test cut.
6.6 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (22) for
sawdust and chips.
The debris bag (22) can be emptied by means of
a zipper at the bottom (1).
6.7 Replacing the saw blade (Fig. 1, 16)
•
Warning! Before changing the saw blade: Pull
out the power plug!
•
Caution! Wear work gloves to prevent injury
when changing the saw blade.
•
Swing the machine head upwards (4).
•
Undo the screw (44) on the cover plate (43)
of the saw blade.
•
Pull back the adjustable blade guard (6) and
at the same time turn the cover plate to achie-
ve access to the flange bolt.
•
Push up the cover plate (43) far enough for
you to be able to screw in the screw (44)
again by approx. 5 turns. The flange bolt (31)
is now accessible for changing the saw blade.
•
Press the saw shaft lock (5) with one hand
while positioning the hexagon key 6mm (41)
on the flange bolt (31) with the other hand.
•
The saw shaft lock (5) engages after no more
than one rotation.
•
Now, using a little more force, slacken the
flange screw (31) in the clockwise direction.
•
Turn the flange screw (31) right out and remo-
ve the external flange (32).
•
Take the blade (7) off the inner flange and pull
out downwards.
•
Carefully clean the flange screw (31), outer
flange (32) and inner flange.
•
Fit and fasten the new saw blade (7) in rever-
se order.
•
Caution! The cutting angle of the teeth, in
other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
Anl_TC_SM_2131_1_Dual_SPK8.indb 47 Anl_TC_SM_2131_1_Dual_SPK8.indb 47
GB
•
Finally, the screw (44) and the cover plate
(43) must be screwed tight again in bottom
position.
•
Warning! Check that the safety devices are in
good working condition before you fit the
power plug again.
•
Warning! Every time that you change the saw
blade, check that the saw blade guard (6)
opens and closes again in accordance with
requirements. Also check that the saw blade
(7) spins freely in the saw blade guard (6).
•
Warning! Every time that you change the saw
blade, check to see that it spins freely in the
table insert (12) in both perpendicular and
45° angle settings.
•
Warning! You should replace the table insert
(12) immediately whenever it is worn or dam-
ged. To do so, undo the Philips screws in the
table insert (12) and take the table insert out
of the fixed saw table (18). To fit the new table
insert (12), proceed in reverse order.
•
Warning! The work to change and align the
saw blade (7) must be carried out correctly.
6.8 Transport (Fig. 1-3)
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Activate the release lever (3), press the ma-
chine head (4) downwards and secure with
the safety pin (25). The saw is now locked in
its bottom position.
•
Fix the saw's drag function with the locking
screw for drag guide (24) in rear position.
•
Carry the equipment by the fixed saw table
(18).
•
To set up the equipment again, proceed as
described in section 5.2 and 5.3.
6.9 Operating the laser (Fig. 1,17)
To switch on: Move the ON/OFF switch (37) to
the "I" position to switch on the laser (35). A laser
line is projected onto the material you wish to pro-
cess, providing an exact guide for the cut.
To switch off : Move the ON/OFF switch (37) to
the "0" position.
- 47 -
09.07.2020 11:13:38 09.07.2020 11:13:38