EINHELL TC-AG 115 Manual De Instrucciones Original página 18

Ocultar thumbs Ver también para TC-AG 115:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 87
5.2 Setting the guard (Fig. 3)
Warning!
Switch off the tool. Pull the power plug.
Adjust the guard (4) to protect your hands
so that the material being ground is directed
away from your body.
The position of the guard (4) can be adjusted
to any specific working conditions. Undo the
screw (a) and turn the cover (4) into the requi-
red position.
Ensure that the guard (4) correctly covers the
gear wheel casing.
Retighten the screw (a).
Ensure that the guard (4) is secure.
Take care that the safety device is secure.
Never use the angle grinder without the
guard.
5.3 Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at
least 1 minute with the grinding or cutting wheel
fi tted in place. Vibrating wheels are to be replaced
immediately.
6. Operation
6.1 Switch (Fig. 4)
The angle grinder comes with a safety switch
which is designed to prevent accidents. To switch
on, press down the On/O switch (2) at the back,
push it forwards and then press it down at the
front. To switch o the angle grinder, depress the
On/O switch (2) at the back. The On/O switch
(2) will jump back into its starting position.
Restart safeguard
If the mains power supply is interrupted when the
switch is locked in the On position, the electric
tool will not run after the power supply is restored.
For the equipment to run, the switch must be tur-
ned o and then on again.
Wait until the machine has reached its top
speed. You can then position the angle grin-
der on the workpiece and machine it.
6.2 Changing the grinding wheels (Fig. 5)
Use the face spanner (5) supplied to change the
grinding wheels. The face spanner (5) is stored in
the additional handle (3). Pull the face spanner (5)
out of the additional handle (3) when you need it.
GB
Important! For safety reasons, the angle grinder
must not be operated with the face spanner (5)
inserted in it.
Warning!
Pull out the power plug.
Notice!
Only ever press the spindle lock when the
motor and grinding spindle are at a stand-
still! You must keep the spindle lock pressed
while you change the wheel!
For grinding or cutting wheels up to approx. 3 mm
thick, screw on the fl ange nut with the fl at side
facing the grinding or cutting wheel.
6.3 Flange arrangements when using grin-
6.4 Motor
It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilati-
on holes clean at all times.
- 18 -
www.sidirika-nikolaidi.gr
Simple wheel change by spindle lock:
Press the spindle lock and allow the grinding
wheel to latch in place.
Open the flange nut with the face spanner.
(Fig. 5)
Change the grinding or cutting wheel and
tighten the flange nut with the face spanner.
ding wheels and cutting wheels (Fig. 6-9)
Flange arrangement when using a de-
pressed-centre or straight grinding wheel
(Fig. 7)
a) Clamping flange
b) Flange nut
Flange arrangement when using a de-
pressed-centre cutting wheel (Fig. 8)
a) Clamping flange
b) Flange nut
Flange arrangement when using a straight
cutting wheel (Fig. 9)
a) Clamping flange
b) Flange nut

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Tc-ag 75011017

Tabla de contenido