Sauder Palladia 412902 Manual De Instrucciones
  1. Manuales
  2. Marcas
  3. Sauder Manuales
  4. Muebles de Interior
  5. Palladia 412902
  6. Manual de instrucciones
Sauder Palladia 412902 Manual De Instrucciones

Sauder Palladia 412902 Manual De Instrucciones

Escritorio ejecutivo
Ocultar thumbs
Tabla de contenido

Publicidad

Enlaces rápidos

Descargar este manual
sauder.com
Executive Desk
Palladia Collection | Model 412902
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
Get executive
with this decision.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-40
Français pg 41-46
Español pg 47-52
Lot # 516051
03/28/18
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicidad

Tabla de contenido
loading

Manuales relacionados para Sauder Palladia 412902

Resumen de contenidos para Sauder Palladia 412902

  • Página 1 Palladia Collection | Model 412902 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
  • Página 2 D708 LARGE DRAWER BOTTOM (2) KEYBOARD SHELF (1) RIGHT BOTTOM MOLDING (2) D716 DRAWER BOTTOM (4) LARGE DRAWER BOX FRONT (2) TOP FRONT MOLDING (1) LEFT UPRIGHT (1) LARGE RIGHT DRAWER FRONT (1) HALF DISK (8) Page 2 412902 www.sauder.com/services...
  • Página 3 Part Identifi cation www.sauder.com/services 412902 Page 3...
  • Página 4 Part Identifi cation D716 D716 D716 D708 D716 D708 Page 4 412902 www.sauder.com/services...
  • Página 5 (EXTENSION SET SHOWN SEPARATED) FILE GLIDE - 4 FILE ROD - 4 EXTENSION RAIL - 8 EXTENSION SLIDE - 8 40NA 40NC HIDDEN CAM - 8 CAM DOWEL - 8 7F TWIST-LOCK ® FASTENER - 25 www.sauder.com/services 412902 Page 5...
  • Página 6 FRONT BRACKET - 4 14H HINGE - 2 KNOB - 8 KEYBOARD HINGE - 2 FELT DISC CARD - 1 GROMMET CAP - 2 CORD CLIP - 1 GROMMET - 3 RUBBER SLEEVE - 4 METAL PIN - 12 Page 6 412902 www.sauder.com/services...

  • Página 7: Tabla De Contenido

    SILVER 5/8" FLAT HEAD SCREW - 4 SILVER 1-1/4" MACHINE SCREW - 4 GOLD 1" MACHINE SCREW - 4 100S BLACK 2-3/4" FLAT HEAD SCREW - 3 SILVER 9/16" LARGE HEAD SCREW - 2 113S BLACK 1-15/16" FLAT HEAD SCREW - 8 www.sauder.com/services 412902 Page 7...
  • Página 8 fl oor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=2076 To begin assembly, push a SAUDER TWIST-LOCK® å to watch a video on how to assemble your unit. FASTENER (7F) into the large holes in the OUTER ENDS (A).
  • Página 9 Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow (8 used) Arrow Insert the metal end of the CAM DOWEL into the HIDDEN CAM. www.sauder.com/services 412902 Page 9...
  • Página 10 NOTE: The EXTENSION SLIDES will be used later for the DRAWERS. å 40NC 40NA Push the black lever in and pull the SLIDE from the RAIL. GOLD 5/16" FLAT HEAD SCREW (16 used in this step) Open end Open end Open end Open end Page 10 412902 www.sauder.com/services...

  • Página 11: Black 9/16" Large Head Screw

    Push the black lever in and pull the SLIDE from the RAIL. Open end GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Open end Open end (4 used) Open end BLACK 9/16" LARGE HEAD SCREW (4 used for the ANGLE BRACKETS) www.sauder.com/services 412902 Page 11...
  • Página 12 5/16" FLAT HEAD SCREWS (3S). NOTE: The CABINET RAILS are marked "CABINET å RIGHT" and "CABINET LEFT" for easy identifi cation. Roller end GOLD 5/16" FLAT HEAD SCREW (4 used in this step) These holes must be here. Roller end Page 12 412902 www.sauder.com/services...
  • Página 13 Tap four MOLDING CONNECTORS (17F) into the å notches in the TOP MOLDINGS (LL and UU) and SIDE MOLDINGS (NN). Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS. Flat end Flat end www.sauder.com/services 412902 Page 13...

  • Página 14: Black 1-1/4" Flat Head Screw

    MOLDINGS (NN) to the TOP (F2). Use sixteen BLACK 1-1/4" FLAT HEAD SCREWS (7S). BLACK 1-1/4" FLAT HEAD SCREW (16 used in this step) The TOP REAR MOLDING (LL) has more holes. The large holes must be here. Page 14 412902 www.sauder.com/services...
  • Página 15 Fasten the UPPER BACK MOLDING (MM) to the TOP å REAR MOLDING (LL) on the TOP (F2). Tighten three TWIST-LOCK® FASTENERS. ® How to use the SAUDER TWIST-LOCK FASTENER Edge and surface with 1. Insert the dowel end of the FASTENER into the TWIST-LOCK® FASTENERS hole of the adjoining part.

  • Página 16: Brown 1" Flat Head Screw

    OUTER ENDS. The larger hole should be facing up. BROWN 1" FLAT HEAD SCREW (8 used in this step) (20 used) BLACK 9/16" LARGE HEAD SCREW (20 used for the ANGLE BRACKETS) Page 16 412902 www.sauder.com/services...
  • Página 17 L O C T E N ® E R S S u r f a c I S T - i t h o F A S L O C T E N ® E R S www.sauder.com/services 412902 Page 17...
  • Página 18 These holes must be here. Use outer holes. Use outer holes. BLACK 9/16" LARGE HEAD SCREW (20 used for the ANGLE BRACKETS) Use outer holes. The MOLDING (M26) should be centered over the HALF DISK (VV). Page 18 412902 www.sauder.com/services...
  • Página 19 T E N ® E R S (4 used) S u r f a c I S T - i t h o F A S L O C T E N ® E R S Open end www.sauder.com/services 412902 Page 19...

  • Página 20: Black 1-15/16" Flat Head Screw

    BACK (J) into the holes in the LEFT END (C3). 113S The large holes must be here. 113S BLACK 1-15/16" FLAT HEAD SCREW (4 used in this step) n i s h U n fi f a c s u r (4 used) Page 20 412902 www.sauder.com/services...
  • Página 21 T E N ® E R S S u r f a c I S T - i t h F A S L O C Roller end T E N ® E R S Open end www.sauder.com/services 412902 Page 21...

  • Página 22: Black 1-9/16" Flat Head Screw

    Push the CORD CLIP (9P) into the hole in the TOP (F2). å Unfi nished surface NOTE: The CORD CLIP is used to å manage your cords. 100S Rounded edge Curved edge 113S BLACK 1-15/16" FLAT HEAD SCREW (4 used for the UPRIGHTS) Page 22 412902 www.sauder.com/services...
  • Página 23 Tighten Risk of damage or Arrow injury. HIDDEN CAMS must be completely Arrow Maximum tightened. HIDDEN 210 degrees CAMS that are not completely tightened may loosen, and parts may separate. To Minimum completely tighten: 190 degrees www.sauder.com/services 412902 Page 23...
  • Página 24 Fasten the BRACES (K) to the OUTER ENDS (A), å UPRIGHTS (D2 and E2), and BOTTOMS (G2). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (16 used for the ANGLE BRACKETS) Page 24 412902 www.sauder.com/services...
  • Página 25 Fasten the BRACES (K) to the OUTER ENDS (A), å UPRIGHTS (D2 and E2), and BOTTOMS (G2). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (16 used for the ANGLE BRACKETS) www.sauder.com/services 412902 Page 25...
  • Página 26 Use twenty-four BLACK 1-1/4" FLAT HEAD SCREWS (7S). BLACK 1-1/4" FLAT HEAD SCREW (24 used in this step) Use outer holes. Finished edge Edge without HALF DISK Edge without HALF DISK Use outer holes. Finished edge Edge without HALF DISK Page 26 412902 www.sauder.com/services...
  • Página 27 Step 20 Fasten the HINGES (14H) to the DOOR (L). Use four å BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (4 used in this step) www.sauder.com/services 412902 Page 27...
  • Página 28 PINS (1R). Insert the METAL PINS into the hole locations of your choice in the LEFT END (C3) and LEFT UPRIGHT (E2). Set the ADJUSTABLE SHELF (M) onto the METAL PINS. Hinge Insert a GROMMET (10P) into the large hole in å the BOTTOM (G2). (4 used) Page 28 412902 www.sauder.com/services...
  • Página 29 To adjust the DOOR in or out (depth), loosen the mounting screw å one turn and move the DOOR in or out, as needed. Tighten the mounting screw after making adjustments. Mounting screw (depth) Adjusting screw (horizontal) (vertical adjustment) www.sauder.com/services 412902 Page 29...
  • Página 30 Use two BLACK 1-1/4" FLAT HEAD SCREWS (7S). Finished edge Finished surface Short fi nished edge BLACK 1-1/4" FLAT HEAD SCREW (6 used in this step) Finished edge These holes must be here. Short fi nished edge Page 30 412902 www.sauder.com/services...
  • Página 31 Fasten the KEYBOARD HINGES (12H) to the KEYBOARD SHELF (R). å Use two SILVER 9/16" LARGE HEAD SCREWS (54S). SILVER 5/8" FLAT HEAD SCREW SILVER 9/16" LARGE HEAD SCREW (4 used in this step) (2 used in this step) www.sauder.com/services 412902 Page 31...
  • Página 32 Fasten two KNOBS (33K) to the KEYBOARD FRONT (O). å Use two GOLD 1" MACHINE SCREW (50S). Roller end GOLD 1" MACHINE SCREW (2 used for the KNOBS) Roller end BROWN 1" FLAT HEAD SCREW (4 used for the DRAWER SLIDES) Page 32 412902 www.sauder.com/services...
  • Página 33 Be sure the grooves in each part line up with each other on the inside of the drawer. Use top hole. Groove Groove BLACK 1-9/16" FLAT HEAD SCREW (16 used in this step) Use top hole. Groove www.sauder.com/services 412902 Page 33...
  • Página 34 Slide the DRAWER BOTTOMS (D708 and D716) into the grooves å in the DRAWER SIDES (D33, D32, D34, D35, D36, and D37) and DRAWER BACKS (D78, D77, and D74). Repeat this step for the other drawers. å D716 D716 D708 Page 34 412902 www.sauder.com/services...
  • Página 35 PAN HEAD SCREWS (9S). Repeat this step for the other drawers using å the LEFT DRAWER FRONTS (BB and GG). BLACK 1-1/8" PAN HEAD SCREW (8 used for the DRAWER FRONTS) These edges should be even. www.sauder.com/services 412902 Page 35...
  • Página 36 (8 used in hole #1 in the SLIDES) Open end SILVER 1-1/4" MACHINE SCREW (2 used for the KNOBS on the DRAWERS) Open end 40NC GOLD 5/16" FLAT HEAD SCREW (8 used in hole #3 in the SLIDES) Page 36 412902 www.sauder.com/services...
  • Página 37 Repeat this step for the other large drawer using the å LARGE LEFT DRAWER FRONT (U). BLACK 9/16" LARGE HEAD SCREW (8 used for the BRACKETS) BLACK 1-1/8" PAN HEAD SCREW (8 used for the DRAWER FRONTS) These edges should be even. www.sauder.com/services 412902 Page 37...
  • Página 38 Open end Insert the FILE RODS into the holes of your choice in the FILE GLIDES, depending on your fi le sizes. (4 screws per drawer) GOLD 5/16" FLAT HEAD SCREW (8 used in this step) Page 38 412902 www.sauder.com/services...
  • Página 39 Lift the front of the SHELF up and slide it into the unit. Click the inner cartridge into place against the black tab. Front Extension Rail Inner cartridge Black tab www.sauder.com/services 412902 Page 39...
  • Página 40 This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. å And to celebrate, why not share your success story? 10 lbs. 75 lbs. 20 lbs. 15 lbs. 30 lbs. 15 lbs. each 30 lbs. 10 lbs. Page 40 412902 www.sauder.com/services...
  • Página 41 élément et conserver le livret pour future référence. EXTRÉMITÉ EXTERNE ..........2 M26 MOULURE .................4 Pour contacter Sauder EXTRÉMITÉ DROITE ..........1 PLINTHE ................4 en ce qui concerne cet EXTRÉMITÉ GAUCHE ..........1 DEVANT DE TABLETTE DE CLAVIER ...1 élément, faire référence...
  • Página 42 12H CHARNIÈRE DE TABLETTE DE CLAVIER ..............2 14H CHARNIÈRE ..............2 33K BOUTON ................8 FICHE DE TAMPONS EN FEUTRE....1 COUVERCLE DE PASSE-CÂBLES ....2 CLIP POUR CORDONS ...........1 10P PASSE-CÂBLES ............3 GOUPILLE EN MÉTAL ...........12 MANCHON EN CAOUTCHOUC .....4 Page 42 412902 www.sauder.com/services...
  • Página 43 Pour commencer l'assemblage, enfoncer une FIXATION trous dans les EXTRÉMITÉS et les MONTANTS. Faire tourner une TWIST-LOCK® SAUDER (7F) dans les gros trous des VIS dans ce trou. EXTRÉMITÉS EXTERNES (A).
  • Página 44 Fixer les ENTRETOISES (K) aux EXTRÉMITÉS EXTERNES (A), NOIRES (1S) à travers les CONSOLES EN MÉTAL sur la MONTANTS (D2 et E2) et DESSOUS (G2). Utiliser huit VIS NOIRES MOULURE ARRIÈRE SUPÉRIEURE et dans les MONTANTS. TÊTE LARGE 14 mm (1S). Page 44 412902 www.sauder.com/services...
  • Página 45 Répéter cette étape pour les autres tiroirs. Pour ajuster la PORTE vers l'intérieur où vers l'extérieur (profondeur), desserrer la vis de montage un tour et déplacer la PORTE vers l'intérieur ou vers l'extérieur. Serrer la vis de après avoir ajusté. www.sauder.com/services 412902 Page 45...
  • Página 46 Fixer le DEVANT DROIT DE GRAND TIROIR (T) au DEVANT DE CAISSON DU GRAND TIROIR (S). Utiliser quatre VIS NOIRES TÊTE GOUTTE DE SUIF 28 mm (9S). Répéter cette étape pour l'autre grand tiroir en utilisant le DEVANT GAUCHE DE GRAND TIROIR (U). Page 46 412902 www.sauder.com/services...
  • Página 47 EXTREMO DERECHO ..........1 CARA DE ESTANTE DE TECLADO ....1 pour future référence. Pour contacter Sauder EXTREMO IZQUIERDO ..........1 DORSO DE ESTANTE DE TECLADO ..... 1 en ce qui concerne cet PARAL DERECHO ............1 LADO DE ESTANTE DE TECLADO ....
  • Página 48 12H BISAGRA DE ESTANTE DE TECLADO ..2 14H BISAGRA ................2 33K POMO ..................8 TARJETA CON TOPES DE FIELTRO ....1 CUBIERTA DE OJAL ..........2 GRAPA DEL CABLE ............1 10P OJAL ..................3 ESPIGA DE METAL ..........12 MANGUITO DE GOMA ...........4 Page 48 412902 www.sauder.com/services...
  • Página 49 Fije cuatro SOPORTES ANGULARES (27G) al EXTREMO Para comenzar el ensamblaje, empuje un SUJETADOR DERECHO (B3) y al PARAL DERECHO (D2). Utilice cuatro TWIST-LOCK® SAUDER (7F) dentro de los agujeros grandes TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). de los EXTREMOS EXTERIORES (A).
  • Página 50 NEGROS DE CABEZA GRANDE de 14 mm (1S). y E2). Introduzca cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S) por entre los SOPORTES DE METAL en la MOLDURA POSTERIOR SUPERIOR y por entre los PARALES. Page 50 412902 www.sauder.com/services...
  • Página 51 Para ajustar la PUERTA hacia atrás o hacia adelante (profundidad), afl oje el tornillo de montaje una vuelta y mueva la PUERTA hacia el interior o hacia el exterior según sea necesario. Apriete el tornillo de montaje después de hacer los ajustes. www.sauder.com/services 412902 Page 51...
  • Página 52 Fije la CARA DERECHA DE CAJÓN GRANDE (T) al FRENTE DE CAJÓN GRANDE (S). Utilice cuatro TORNILLOS NEGROS DE CABEZA REDONDA de 28 mm (9S). Repita este paso para el otro cajón grande utilizando la CARA IZQUIERDA DE CAJÓN GRANDE (U). Page 52 412902 www.sauder.com/services...
  • Página 53 à Les téléviseurs peuvent être particulièrement un téléviseur. cet eff et. lourds. De plus, le poids et l’emplacement du tube image ont tendance à rendre les téléviseurs instables et enclins à tomber vers l’ a vant. www.sauder.com/services 412902 Page 53...
  • Página 54 Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y propensa a volcarse hacia adelante. Page 54 412902 www.sauder.com/services...
  • Página 55 à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
  • Página 56 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.

Tabla de contenido