Ryobi WS750L Manual Del Operador página 15

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

 Hold the material firmly against the rip guide and feed
the material into the cutting wheel.
 Make the cut far enough into the material without over-
cutting.
 Turn the on/off switch to the OFF position.
 Turn the material over and make the cut along one of the
marks. This time overcut the other line and the cut piece
should separate from the rest of the material.
 Turn the on/off switch to the ON position.
 Turn the flow adjustment valve to the ON position.
 Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
 When the cut is made, turn the saw OFF. Wait for the cut-
ting wheel to come to a complete stop before removing
any part of the material.
TO MAKE A BEVEL CUT
See Figure 28, page 25.
Beveled 45° cuts can be made by adjusting the position of
the motor head.
 Using a marker or grease pencil, mark the area to be cut
on material.
 Loosen the lock knob on the back of the motor head.
Pivot the motor head to the full 45° angle.
 Tighten the lock knob securely.
 Set the rip guide to the desired setting, lock in place, and
tighten the lock knob.
 Place the material on the table and firmly against the rip
guide and fence.
 Make sure the material is clear of the cutting wheel before
turning on the saw.
 Turn the on/off switch to the ON position.
 Turn the flow adjustment valve to the ON position.
 Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
 Hold the material firmly against the rip guide and feed
the material into the cutting wheel.
 When the cut is made, turn the saw OFF. Wait for the
cutting wheel to come to a complete stop before removing
any part of the material.
TO MAKE A PLUNGE CUT
See Figure 29, page 25.
Plunge cuts are made by positioning the material directly
underneath the cutting wheel and lowering the wheel onto
the workpiece. This allows pieces to be cut from the center
of the material.
 Using a marker or grease pencil, mark the area to be cut
on material.
OPERATION
 Loosen the lock knob on the top of the motor head and
pull the motor head upward to its maximum height. Tighten
the lock knob.
 Secure the material on the table underneath the cutting
wheel.
 Turn the on/off switch to the ON position.
 Turn the flow adjustment valve to the ON position.
 Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
 Hold the motor head firmly by the handle and loosen the
lock knob.
 Slowly lower the motor head into the material to make
the cut.
 Raise the motor head and tighten the lock knob.
 Turn the on/off switch to the OFF position.
 Turn the flow adjustment valve to the OFF position.
 Slide the table away from the motor head and position
the work material for the next cut.
TO FOLD THE SAW FOR STORAGE AND
TRANSPORTATION
See Figures 30 - 31, page 26.
The leg stand can be collapsed for storing or transporting
the saw.
 Drain water from the water tray. Disconnect the hoses
and wipe the tray out with a clean, dry cloth.
 Unplug the saw and secure the power cord inside the
tray.
 Make sure the knobs on the motor head are tightened.
 Set and lock the rip guide at an angle as shown in Figure
31. This will help keep the table from sliding too far out
of place when the saw is set on end.
 Set the saw upright on its wheel end.
 Pull the lock knob to collapse the leg stand. Slide and
push leg sections 2 and 3 toward the wheel end.
 Push the legs together until the lock knob locks into place
on the leg stand.
NOTE: The ridged area on the end of the frame may be used
as a handle for moving and transporting the saw.
15 — English

Publicidad

Tabla de contenido
loading

Tabla de contenido