Lcd Display; Setup Menu - JB Systems MSD 900 Manual De Instrucciones

ENGLISH
button (5). If you turn it to the right, you will hear the mixed output signal. In the middle position
the cue signals and output signal are mixed.
28. CUE LEVEL: Used to adjust the output level of the Headphones. Note that, due to the high output
power, you can permanently damage your ears! Do not play at high volume!
FUNCTIONS (rear)
29. AUDIO OUTPUT from right player: Output for the audio signal from the right player. Use the supplied
cinch/cinch cables to connect these outputs to the CD/line input of an external mixing unit.
30. AUDIO OUTPUT from left player or mixer: Output depends on the MIXER MODE you selected in the
setup menu (see chapter SETUP MENU for more information):
 MIXER MODE = Ext -Tone: output for the audio signal from the left player. Use the supplied
cinch/cinch cables to connect these outputs to the CD/line input of an external mixing unit.
 MIXER MODE = Ext +Tone: same as "Ext –Tone" but now the tone controls can be used.
 MIXER MODE = internal mixer: for the audio signal from the mixer. Use the supplied
cinch/cinch cables to connect this output to the input of an amplifier or powered speaker
cabinets.
31. FADER START Sockets: If you are using a mixer with fader start function, connect the player with the
fader start of the mixer. Please note that these sockets must never be connected with any voltage.
Attention: This remote control is only compatible with certain (Synq® or Pioneer® compatible) mixers.
32. POWER ADAPTER input: connect the supplied 6Vdc adapter here.

LCD DISPLAY

1. PLAY/PAUSE indicators: displays the status of the player.
2. CUE: appears when the master cue point is programmed.
3. FOLDER: Shows the current folder number.
4. TRACK: Shows current track number.
5. MINUTE: Shows "minutes" time information of current track.
6. SECOND: Shows "seconds" time information of current track.
7. FRAME: Shows "frame" time information of current track. (1 frame = 1/75
8. TIME BAR: shows either remaining or elapsed time. Starts flashing at the end of each track to alert the
user to take action.
9. BPM DISPLAY: the automatic beat counter shows the number of Beats Per Minute on the display.
When you selected "CUE SYSTEM = BPM/TAP" in the setup menu, you can choose between manual
mode (the display only shows the BPM value) and automatic mode (the display shows "AUTOBPM").
JB SYSTEMS
®
OPERATION MANUAL
th
sec.)
7/78 MSD-900
ENGLISH
10. PITCH DISPLAY: Shows the actual percentage of speed change, selected with the SPEED slider. The
small padlock is shown when the pitch lock function (Master Tempo) is active.
11. LOOP: shows when a loop is programmed. (repeating a particular area)
 LOOP Flashing: Loop is programmed and currently playing.
 LOOP stays on: Loop is programmed but not playing.
12. AUTO CUE: appears when the "auto cue" function is active. (see chapter SETUP MENU for more
information)
13. ELAPSED, REMAIN: indicates that the time shown on the display is the elapsed or remaining time for
the playing track. (see chapter SETUP MENU for more information)
Note: for MP3 files it's not possible to show the total remaining time for all tracks on the memory device.
14. ALPHANUMERIC DISPLAY: Shows the names of folders and MP3 tracks. For MP3 tracks recorded in
CBR also the bit rate is shown. For VBR recorded MP3 tracks the display only shows "VBR". All kinds of
other interactive information is also shown.
15. RANDOM: is shown when the left player is in random mode.
16. SINGLE: appears when the unit is set to play just one track at a time. When it is not shown, the player
plays continuously through all tracks. (see chapter SETUP MENU for more information)

SETUP MENU

In the setup menu you can adapt several parameters of the
MSD900 to your personal taste. To access the setup menu,
just press the SEARCH button (3) for about 1.5sec: he
display shows "SETUP MENU" while the red SEARCH button
(serves as NO-button) and green BPM/CUE button (serves
as YES-button) are both lit. You can browse the setup menu
with the JOG wheel (4). Use the YES button to select
submenus and options, use the NO button to return to the
main menu. To leave the setup menu, press the SEARCH
button (3) again for about 1.5seconds. Below please find the
explanation of the different sub menus and options:
PITCH BEND:
The pitch bend parameter determines the impact of the jog
wheel on the pitch bend function. The CD-player comes with
the pitch bend parameter set to 50. You can adjust the
parameter between 001 (very little impact) to 100 (extreme
impact) to adapt the pitch bend function perfectly to your
personal taste! You can select different values for the left and
right players.
TIME MODE:
Used to select if you want to see the remaining or elapsed
time of the selected track on the display. You can select a
different time display for the left and right players.
PLAY MODE:
For each deck you can choose a different play mode:
 Continuous play: all tracks on the memory device will be
played without interruption. (mostly used in pubs)
 Single + autocue: player stops at the end of each track
and waits at the first music note of the next track. (mostly
used by deejays) This means that badly indexed CDs will
not interfere with the instant start capabilities of the player.
This is a very useful feature for deejays!
 Single no autocue: player stops at the end of each track
and waits at the beginning of the next track, not at the first
music note!
JB SYSTEMS
®
OPERATION MANUAL
8/78 MSD-900