Some Important Facts About Wine; Power Supply; Installing Your Wine Cabinet - ARTEVINO OXG1T230NPD Modo De Empleo

Some important facts about wine

Your ARTEVINO wine cabinet has been designed to guarantee optimal storage and/or serving conditions
for your wine.
Wine is a complex product. It develops very slowly and requires specific conditions in order to reach its
full potential.
All wines are stored at the same temperature. Only their serving temperatures differ.
This being the case, just like the natural cellars of wine producers, it is not so much the absolute value
of the storage temperature that is important but its consistency. In other words, whatever temperature
your cabinet is set at (between 10°C and 14°C for a maturing cabinet), your wine will be stored in ideal
conditions provided that this temperature does not fluctuate.
IN ANY EVENT, IF YOU NOTICE A HUMIDITY OR TEMPERATURE FAULT INSIDE YOUR WINE
CABINET, BE AWARE THAT ONLY PROLONGED EXPOSURE TO ABNORMAL CONDITIONS
IS HARMFUL TO YOUR WINES.

Power supply

For your personal safety, the wine cabinet must be correctly earthed.
Ensure that the socket is correctly earthed and that your installation is protected by a circuit breaker
(30 mA*)
*Not applicable to some countries.
All work must be carried out by a qualified electrician.

Installing your wine cabinet

• When unpacking your cabinet, check that it is not damaged (signs of impact, buckling, marks).
• Remove the protective elements found inside and outside your cabinet including the lower hinge
protector (see diagram (1))
• Fit the cap (see diagram 2), found in the accessories bag, used for sealing the hole in the lower hinge.
• Open the door and check that the various elements are intact.
1
2
Protective wedges for transportation have been attached to each shelf. 2 wedges per shelf (Picture 1).
Remove all of them using a rotating movement (Picture 2). You can retain these wedges and reuse them if
you have to transport your wine cabinet over a long distance.
6
Picture 2
Picture 1
• Arrange the electric power lead so that it does not come
into contact with any of the cabinet's components.
• Install the stop at the back of the cabinet (see diagram).
This allows a space of 7 cm to be maintained between the
wall and the rear of the cabinet. This space allows your
cabinet's power consumption to be optimised.
• Place the 2 caps in the 2 holes at the top of the cabinet,
ensuring that you do not push them all the way in.
• Slide the rear stop between the caps and the wall of the
cabinet, then push the 2 caps all the way in.
• Place your cabinet in the desired location.
The location that you choose for your cabinet must:
- be open to the outside and well ventilated (not in an
enclosed cupboard, for example),
- allow there to be a minimum space of 7 cm between the wall and the back of the cabinet,
- not be close to any source of heat,
- not be too damp (utility room, laundry room, bathroom...),
- have a flat, stable floor,
- be supplied with standard accessible power (outlet that complies with standards in force in your country,
earthed with circuit breaker).
It is forbidden to use an extension cord or adaptor.
Fitting the handle
In order to correctly fit the handle on your wine cabinet's solid door, please
follow these instructions.
Prepare the items required for assembly, supplied with your cabinet:
- The handle ,
1
- 2 handle tubular supports ,
2
- 2 washers 3 ,
- 2 screws 4 ,
- 2 caps .
5
You will also need a flathead screwdriver (not supplied)
Instructions :
1. Insert 1 washer on 1 screw.
2. Insert the handle tubular support then the screw in the hole provided on the inside of the wine cabinet
door.
3. Use the screwdriver to screw the screw into the handle post and gently tighten.
4. Place the cap on the screw head.
5. Repeat this procedure for the other handle post.
Recommendation
To allow you to easily level your wine cabinet, it is fitted with 2 adjustable feet at the front.
Carry out final levelling of your cabinet (spirit level recommended).
WAIT 48 HOURS BEFORE PLUGGING IN YOUR APPLIANCE
When moving your cabinet, never tilt it more than 45°, and always on its side (on the opposite side of
the flexible lead).
1 5 4 3 2 1
GB
7