Commissioning And Temperature Setting - ARTEVINO OXG1T230NPD Modo De Empleo

Commissioning and temperature setting

Commissioning
After waiting 48 hours, plug in your wine cabinet, having checked that your socket is correctly
supplied with power
(presence of correct sized fuses, circuit breaker in working order. If need be, plug in another electrical
appliance to check the power supply).
Humidity
Your cabinet is fitted with an exclusive ARTEVINO system allowing you to recreate inside your wine
cabinet the level of humidity required to effectively seal your bottles' corks. When installing your cabinet, it
is important to pour the equivalent of one glass of water onto the floor of the cabinet to reach an optimal
hygrometry rate.
Temperature setting
Description of the control panel
1
2
3
4
• Temperature display: displays the actual temperature inside your wine cabinet. It is therefore
necessary to wait before your new setting takes effect.
Status lights:
Compressor 1 : indicates that the compressor is operating. When this flashes, it means that the
compressor is going to start up in a few minutes (technical delay).
Defrosting cycle 2 + : indicates that an automatic defrosting cycle is underway.
Heater 3 : indicates that the heater is operating.
Alarm 4 : informs you that there is an abnormally high or low temperature inside the wine cabinet.
Commissioning the control panel
By default, the control is in the OFF position. To switch on the cabinet, press and hold the
several seconds until just the temperature is displayed.
To put the cabinet on standby, press and hold down the
between the internal temperature and the OFF display (the cabinet is no longer operating, only the display
is active).
To reactivate the cabinet back on, press and hold down the
temperature is displayed.
12
button for
button for several seconds. The display switches
button for several seconds until just the
To set the temperature of your wine cabinet
The temperature of your wine cabinet is set entirely from the control panel.
Single-temperature cabinets:
• Press and hold down the SET button for a few seconds until the set temperature (ST1) flashes.
The default temperature setting is 12°C (ideal maturing temperature). However, the temperature
can be set from 9°C - 15°C.
• The recommended temperature setting range for wine storage is 10°C - 14°C.
• Set the desired temperature using the
• Confirm your setting by pressing the SET button. If you do not confirm by pressing this
key, the change in temperature setting will not take effect.
Your wine cabinet must be placed in a room with a temperature of 0°C - 35°C for solid door and 0°C
- 30°C for Glass door.
2 temperatures model:
BEVERAGE CENTER COMPARTMENT (BOTTOM):
Press and hold the SET button for a few seconds until the SET temperature (ST1) flashes.
•
The default temperature setting is 3°C. However, the temperature can be set from 3°C to 6°C
• Set the desired temperature using the
• Maintain pressure on the SET button for a few seconds. This confirms the temperature
setting of the lower compartment of the cabinet (Beverage center) and allows you to access
the temperature setting (ST2) of the upper compartment (aging compartment).
AGING COMPARTMENT (TOP):
• The default temperature is 12°C . However, the temperature can be set from 10°C à 14°C
• Set the desired temperature using the
• Confirm your setting by pressing the SET button. If you do not confirm by pressing this key,
the change in temperature setting will not take effect.
Your wine cabinet must be placed in a room with a temperature of 12°C - 25°C.
3-temperature cabinets:
ZONE IN THE CENTRE OF THE CABINET OR MATURING ZONE:
Press and hold down the SET button for a few seconds until the set temperature (ST1) flashes.
•
The default temperature setting is 12°C (ideal maturing temperature). However, the temperature
can be set from 10°C - 14°C.
• Set the desired temperature using the
Maintain pressure on the SET button for a few seconds. This confirms the temperature setting
•
in the maturing zone and allows you to access the temperature setting of the red wine service
zone (ST2).
RED WINE SERVICE ZONE:
• The default temperature setting is 18°C. However, the temperature can be set from 15°C - 20°C.
• Set the desired temperature using the
• Confirm your setting by pressing the SET buttons. If you do not confirm by pressing this key, the
change in temperature setting will not take effect.
N.B.: the temperature of the lower compartment (chilling compartment) results from the temperature set in the
maturing zone. The temperature gradient between these zones is 4 - 6°C.
N.B.: to function correctly, your cabinet must be placed in a room with a temperature of 12 - 30 °C.
Multi-temperature cabinets:
LOWER ZONE:
• Press and hold down the SET buttons for a few seconds until the set temperature (ST1) flashes.
The default temperature setting is 8°C. However, the temperature can be set from 6°C - 10°C.
• Set the desired temperature using the
• Maintain pressure on the SET buttons for a few seconds. This confirms the temperature setting
in the lower zone of the cabinet and allows you to access the temperature setting of the upper
zone (ST2).
and buttons.
and buttons.
and buttons.
and buttons.
and buttons.
and buttons.
GB
13