Manuales relacionados para Sanus VSF409
Resumen de contenidos para Sanus VSF409
- Página 1 Scan for easy install video THANK YOU FOR CHOOSING SANUS VSF409 THE #1 TV MOUNT BRAND IN THE US. VSF409/415 Instruction Manual Scan for easy install video VSF415...
- Página 2 TWO SIMPLE STEPS TO FINDING YOUR STUDS: Step 1 Holding it vertically, lightly move the SANUS Pull apart the SANUS Magnetic Stud Finder to Step 2 Magnetic Stud Finder up and down while expose the probing pin within. Starting about sliding across your wall.
-
Página 3: Lo Haremos Sin Estrés
VSF409 VSF415 We’ll Make It Stress-Free If you have any questions along the way, just give us a call. 1-800-359-5520 (UK: 0800-056-2853) We’re ready to help! Lo haremos sin estrés Si tiene preguntas mientras realiza la instalación, llámenos. 1-800-359-5520 (Reino Unido: 0800-056-2853) Estamos listos para ayudarlo. - Página 4 Para Español ver página 26 Does your TV No — Perfect! including accessories) 50 lbs. Yes — This mount is NOT compatible. MountFinder.Sanus.com or call weigh more than (22.7 kg) 1-800-359-5520 (UK: 0800-056-2853) to fi nd a compatible mount. 50 lbs. (22.7 kg)?
- Página 5 STEP 1 Attach Bracket to TV Parts and Hardware for STEP 1 WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer;...
- Página 6 1.2 Spacers 1.1 Select TV Screws Hand thread screws into the threaded inserts on the back of your TV : If your TV has a fl at back AND you want your TV closer to the wall, to determine which screw diameter (M4, M6, or M8) to use.
- Página 7 1.3 Measure Your TV Hole Pattern Measure the width and height of your TV hole pattern in mm. Record your measurements: 200 mm Width ________ mm x Height ________ mm [7.87 in.] 200mm x 200mm Go to PAGE 8 200 mm [7.87 in.] 200 mm [7.87 in.]...
- Página 8 1.4 Attach TV Bracket with Extensions [200 x 200 mm ONLY] M4/M6/M8 Flat Back 02 04 05 07 08 10 11 M4 Round Back / Extra Space M6/M8 Round Back / Extra Space 06 09 When fi nished, go to PAGE 13...
- Página 9 1.5 Remove Extensions [200 x 100 mm, 100 x 100 mm, and 75 mm x 75 mm] If mounting to a TV with; 200 x 100 mm (7 ⅞ x 4 in.), 100 x 100 mm (4 x 4 in.), or 75 x 75 mm (3 x 3 in.) hole patterns, remove the extension plates from the TV bracket using a screwdriver and wrench.
- Página 10 1.6 Attach TV Bracket [200 mm x 100 mm] M4/M6/M8 Flat Back 02 04 05 07 08 10 11 M4 Round Back / Extra Space M6/M8 Round Back / Extra Space 06 09 When fi nished, go to PAGE 13...
- Página 11 1.6 Attach TV Bracket [100 mm x 100 mm] M4/M6 Flat back 02 04 05 10 11 M4/M6 Round Back / Extra Space 03 06 12 13 10 11 When fi nished, go to PAGE 13...
- Página 12 1.6 Attach TV Bracket [75 mm x 75 mm] NOTE: If the hole pattern on your TV is 75 x 75 mm, washers M4 Flat back will not be used. Only M4 screws can be used. M4 Round Back / Extra Space When fi...
- Página 13 fi elds may aff ect the operation of those devices, resulting in serious injury or death. If you have an implanted medical device, keep at least 13 cm (5 in.) between your device and the magnet. Please consult with your physician or medical professional prior to using this product. Sanus Magnetic Stud Finder* NOTE: Not all hardware included will be used.
- Página 14 Minimum wood stud size: common 51 x 102 mm (2 x 4 in.) nominal 38 x 89 mm (1½ x 3½ in.) ● Stud center must be verified Locate a nail/screw in the stud using the Sanus magnetic stud fi nder* provided. Find the edges of the stud using the probe of the stud fi...
- Página 15 Level the wall plate template and tape in place. NOTE: For assistance in determining wall plate location, see HeightFinder at sanus.com. IMPORTANT : Be sure you mark and drill into the center of the stud.
- Página 16 Level the wall plate template and mark the hole locations. NOTE: For assistance in determining wall plate location, see Height Finder at sanus.com. Drill two pilot holes using a 10 mm (3/8 in.) diameter drill bit.
- Página 17 fi rmly against the wall plate CAUTION: Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage Do not over- tighten the lag bolts Fit lag bolt covers over lag bolts VSF409 VSF409 VSF415 VSF415...
- Página 18 STEP 3 Hang TV Mount to Arm Parts and Hardware for STEP 3 WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer;...
- Página 19 STEP 3 Hang TV Mount to Arm Fit nut and cover into underside of mount arm Place washer and pivot pin onto mount arm bracket Fit the bracket onto pivot pin . Slide washers and spacer onto mounting bolt and fi t bolt through mounting and pivot pin until it meets nut .
- Página 20 Adjustments A. Use hex key to adjust arm extension tension. B. Adjust rotation/level tension. NOTE: VSF415 shown.
- Página 21 Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! Cable Plate Screws Cable Plate 8-32 x 0.5 in. 8-32 x ½ in. VSF409 VSF409 VSF415 VSF415 Cable Ties VSF409...
- Página 22 Manage Cables Option A: Thread cable through channels the secure with plates and plate screws Option B: Install plates with plate screws . Thread cable ties through end holes in plates . Arrange cables then secure them with the cable ties NOTE: Pull the arm to its full extension before routing the cables through the channels, then loosely route the cables.
- Página 23 Dimensions - VSF409 in. [mm] TV INTERFACE 7.87 200.0 3.94 100.0 7.87 3.94 2.95 3.94 200.0 100.0 75.0 100.0 2.95 75.0 WALL PLATE TOP VIEW - EXTENDED SIDE VIEW - EXTENDED 15° ESTIMATED 20" TV 100X100 VESA CENTERED 60.00° 60.00°...
- Página 24 Dimensions - VSF415 in. [mm] TV INTERFACE 7.87 200.0 3.94 100.0 3.94 2.95 7.87 3.94 100.0 75.0 200.0 100.0 2.95 75.0 WALL PLATE TOP VIEW - EXTENDED SIDE VIEW - EXTENDED 15.3 15.00° ESTIMATED 20" TV 100X100 VESA CENTERED 90° 90°...
-
Página 26: Localizador De Montantes Magnético Sanus
Paso 2 Separe el Localizador de Montantes el Localizador de Montantes Magnético SANUS Magnético SANUS para acceder al alfiler de hacia arriba y hacia abajo deslizándolo por la exploración integrado. Comenzando a 1,2 cm superficie de la pared. El imán integrado será atraído (½... - Página 27 22,7 kg No — ¡Perfecto! 22,7 kg (50 lb), incluidos Sí — Este soporte NO es compatible. Visite MountFinder.Sanus.com o llame al (50 lb) los accesorios? 1-800-359-5520 (Reino Unido: 0800-056-2853) para encontrar un soporte compatible. ¿De qué está...
-
Página 28: Paso 1 Coloque El Soporte En El Televisor
ESPAÑOL PASO 1 Coloque el soporte en el televisor Ver PÁGINA 5 Piezas y elementos de sujeción para el PASO 1 ADVERTENCIA: Este producto contiene piezas pequeñas que podrían causar asfixia si fuesen tragadas. NOTA: No se utilizarán Antes de comenzar a montar la unidad, verifique que todas las piezas estén incluidas y en buen estado. todos los elementos de En caso de que falten piezas o alguna esté... -
Página 29: Paso 2 Coloque La Placa De Pared En La Pared
ESPAÑOL 1,5 Retirar las extensiones - 200 x 100 mm, 100 x 100 mm y 75 x 75 mm Si va a instalar en un televisor con un patrón de orificios de 200 x 100 mm (7 ⅞ x 4 pulgadas), de 100 x 100 mm (4 x 4 pulgadas) o de 75 x 75 mm (3 x 3 pulgadas), retire las placas de extensión de la placa de sujeción del soporte del televisor 01 utilizando un destornillador y una llave inglesa. - Página 30 Nivele la plantilla de la placa de pared y péguela con cinta adhesiva en su posición. NOTA: Si necesita ayuda para determinar la posición de la placa de pared, consulte Height Finder en sanus.com. IMPORTANTE : Asegúrese de hacer las marcas y taladrar en el centro del montante.
-
Página 31: Paso 3 Cuelgue El Soporte De Televisor En El Brazo
Nivele la plantilla de la placa de pared y marque la posición de los orificios. NOTA: Si necesita ayuda para determinar la posición de la placa de pared, consulte Height Finder en sanus.com. Taladre los dos orificios guía utilizando una broca de 10 mm (3/8") de diámetro. -
Página 32: Organización De Cables
ESPAÑOL cubierta sobre el perno de montaje. PRECAUCIÓN: Necesitará ayuda para realizar esta operación. Utilice la llave hexagonal para apretar el perno de montaje y fije el soporte de montaje al brazo. Ajustes Ver PÁGINA 20 A: Utilice la llave hexagonal para ajustar la tensión de extensión del brazo. - Página 33 View step-by-step product videos to ease your install experiences. YOUTUBE.COM/SANUSSYSTEMS Find the latest news stories about your favorite SANUS products. Milestone AV Technologies and its affi liated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations.
- Página 34 If you ever have questions about your SANUS product, give us a call at 1-800-359-5520. We're ready to help! If you ever have questions about your SANUS product, give us a call at 1-800-359-5520. We're ready to help! ‘Monthly prize’...