Publicidad
Idiomas disponibles
Idiomas disponibles
2
Conductor size (mm
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Voltage drops
Inrush currents cause short-time voltage drops.
Under unfavourable power supply conditions,
other equipment may be affected.
If the system impedance of the power supply is lower
than 0.25 ø, disturbances are unlikely to occur.
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Depth of cut adjustment (fig. A & B)
• Loosen the depth adjustment knob (14).
• Move the shoe (6) to obtain the correct depth of
cut.
• Tighten the depth adjustment knob (14).
For optimal results, allow the saw blade
to protrude from the workpiece by about
3 mm (see inset in figure B).
Bevel adjustment (fig. C)
The bevel angle can be adjusted between 0° and 45°.
• Loosen the bevel adjustment knob (11).
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
• Set the bevel angle by tilting the saw shoe (6)
until the mark indicates the desired angle on the
scale.
• Tighten the bevel adjustment knob (11).
Shoe adjustment for 90° cuts (fig. D)
• Adjust the saw to 0° bevel.
• Retract the blade guard using the lever (8) and
60
place the saw on the blade side.
• Loosen the bevel adjustment knob (11).
6
10
• Place a square against the blade and shoe to
15
adjust the 90° setting.
20
– Adjust the stop (16) using an Allen key.
25
-
Replacing the saw blade (fig. E)
-
-
• Engage the blade lock button (4) and unscrew
6
6
the blade clamping screw (17) by turning
6
6
counterclockwise using the spanner (18) supplied
15
with the tool.
15
• Retract the lower blade guard (9) using the lever
20
(8) and replace the blade (10). Reinstall the
-
washers (19 & 20) in the correct position.
• Check the direction of rotation of the blade.
• Thread on the blade clamping screw (17) by hand
to hold the washer in position. Turn clockwise.
• Press the blade lock button (4) while turning the
spindle until the blade stops rotating.
• Tighten the blade clamping screw firmly using the
spanner.
Adjusting the riving knife (fig. E)
For the correct adjustment of the riving knife (7),
refer to the inset in figure E. Adjust the clearance of
the riving knife after changing the saw blade or
whenever necessary.
• Adjust the depth of cut to 0 mm to access the
clamping screws of the riving knife.
• Loosen the screws (21) and pull out the riving
knife to its maximum length.
• Adjust the clearance.
• Tighten the screws (torque: 4 - 5 Nm).
Mounting and adjusting the parallel fence (fig. F)
The parallel fence (15) is used for cutting parallel to
the edge of the workpiece.
Mounting
• Slacken the locking screw (22) as to allow the
parallel fence to pass.
E N G L I S H
29
Publicidad
