Heat / Cool Operating Mode Selection (Operation Mode); Daily Schedule / Climatic Curves / Eco Mode (Preset Temp); Weekly Schedule; Cool Mode Weekly Schedule (Preset Temp. Cool) - Ferroli OMNIA S 3.2 Manual De Instalación, Uso Y Mantenimiento

OMNIA S 3.2
Premere il tasto SW3 , spostarsi tra le righe con i tasti SW1 / SW2, quindi selezionare la riga con il tasto SW3, quindi con i tasti SW6 / SW7

8.5.1 Heat / Cool operating mode selection (Operation Mode)

User menù > Operation mode > select the mode and confirm with the button SW3

8.5.2 Daily schedule / climatic curves / Eco mode (Preset Temp)

User menù > Preset temp >

Weekly schedule

This function acts only on single zone, and if 2 zones are enabled only on zone 1: therefore it has no effect on zone2.
If the unit is in Cool mode, the events to be considered are those in the "Preset Temp. Cool" menu, while if the machine is in Heat mode the events to be considered
are those in the "Preset Temp. Heat" menu.
When the operation mode is changed, the function is automatically deactivated and it is therefore necessary to reset the function.
The current default temperature is invalid when the unit is turned off (OFF).
The unit will operate at the default temperature of the first event following the activation time of the unit itself.

Cool mode weekly schedule (Preset Temp. Cool)

User menù > Preset temp > Preset Temp Cool
The submenu with the 7 days of the week will appear, for each day there are 6 possible events to be set from Event 1 to Event 6 will appear.
Event 1 Enabled y/n
Event 2 Time
Event 3 Temperature
Monday
Event 4
Event 5
Event 6

Heat mode weekly schedule (Preset Temp. Heat)

User menù > Preset temp > Preset Temp Heat
The submenu with the 7 days of the week will appear, for each day there are 6 possible events to be set from Event 1 to Event 6 will appear.
Event 1 Enabled y/n
Event 2 Time
Event 3 Temperature
Monday
Event 4
Event 5
Event 6
The temperature setting remains active until the next enabled event. At the start of this new enabled event, the new associated temperature is set on the machine
and so on.

Climatic curves (Weather Temp Set)

User menù > Preset temp > Weather Temp Set
The function allows you to set the water flow temperature set point for Heat mode and Cool mode as a function of the outside air temperature.
Enabled y/n
Z1 Cool Mode
Clim Curve Sel
Enabled y/n
Z1 Heat Mode
Clim Curve Sel
Enabled
Z2 Cool Mode
Clim Curve Sel
Enabled y/n
Z2 Heat Mode
Clim Curve Sel
When the climatic curves are enabled, it is not possible to modify the T1S set point manually and a warning message will appear.
Modalità Economy (Eco Mode)
User menù > Preset temp > Eco Mode
Enabled y/n yes/no
Clim Curve Sel 1-9
Timer enabled y/n yes/no
Start hh.mm
End hh.mm
If ECO mode is enabled:
• Timer = not enabled, ECO is always active.
Timer = enabled, the start and end times must be set
Enables the Eevent
Start time hh.mm
Water temperature setpoint
Enables the Eevent
Start time hh.mm
Water temperature setpoint
Enables climatic curve for zone 1 in cooling mode
to select the climatic curve in cooling mode
Enables climatic curve for zone 1 in heating mode
to select the climatic curve in heating mode
to select the climatic curve in cooling mode
to select the climatic curve in heating mode
Enables climatic curve for zone 2 in heating mode
to select the climatic curve in heating mode
enables ECO function (not availbale for 2 zones)
select the climatic curve from 1 to 9
Enables the timer
start time
end time
Cod. 3541V941 - Rev. 00 - 09/2021
113
EN