DeWalt DCGG571 Traducido De Las Instrucciones Originales página 37

Intended Use
This grease gun is designed for professionally
dispensing lubricant.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This grease gun is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
LED Worklight (Fig. A, C)
There is an LED worklight 4 located on the top cap
worklight is activated when the trigger switch is depressed
and when the LED worklight button
When the LED worklight button is in the OFF position, the LED
worklight will not turn on when the trigger is depressed. The
worklight will automatically turn off 20 seconds after the trigger
switch is released. If the trigger switch remains depressed, the
worklight will remain on.
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Variable Speed Trigger Switch (Fig. A, D)
Lock-Off Button and Trigger Switch
Your grease gun is equipped with a lock-off button
To lock the trigger switch, press the lock-off button as shown
in Figure D. Always lock the trigger switch
storing the tool to eliminate unintentional starting. The lock-
off button is coloured red to indicate when the switch is in its
unlocked position.
To unlock the trigger switch, press the lock-off button as shown
in Figure D. Squeeze the trigger switch to turn the motor ON.
Releasing the trigger switch turns the motor OFF.
nOTE: The variable speed trigger switch will give you added
versatility. The further the trigger is depressed the higher the
output of grease.

WARNING: This tool has no provision to lock the switch
in the ON position, and should never be locked ON by any
other means.
Pressure Relief Valve (Fig. E)
The pressure relief valve 23 is set at the factory to relieve
pressure above 69 MPa (690 bar). Grease coming out of
the pressure relief valve indicates a clog in the fitting, line
or bearing. Any of these conditions must be corrected
before proceeding.
6 . The
is in the ON position.
5
2 .
1 when carrying or

WARNING: The grease gun may generate high
pressure. Do not remove or tamper with the pressure
relief valve. Serious injury may occur.
Shoulder Strap (Fig. A)
Your grease gun comes with a shoulder strap. Hook the
shoulder strap clips into the shoulder strap clip holes
on the shoulder strap mount 20
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. F)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 16
handle (Fig. F).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. F)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button . A combination of the three green LED lights will
32
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Installing a Grease Cartridge (Fig. A, E, G)
1. Pull the grease tube handle
secure the grease tube rod
moving the rod to the side. Ensure the rod is placed securely
in the slot to prevent it from disengaging.
2. Unscrew the grease tube assembly
3. Remove the plastic cap from the grease cartridge, then
insert the cartridge, open end first, into the grease tube
4. Remove the seal from the other end of the grease cartridge.
EnGLIsh
21 found
.
WALT battery packs and chargers.
16 is fully charged.
with the rails inside the tool's
and firmly pull the
17
12 out as far as it will go, then
13 into the retaining slot 15
14 from the grease gun.
10
by
.
35