Würth DIGA CSM-1 POWER Traducción Del Manual De Instrucciones De Servicio Original página 29

Precautions for the charger and battery
Only use the battery specified for the tool.
■
Never connect the device to a power source
or to any other rechargeable battery, a dry
cell or a vehicle battery. Non-observation
could result in breakages, faults, heat genera-
tion or burns.
Charging must be performed with the speci-
■
fied charger. If charging is performed with a
different charger, malfunctions can occur, or
the device might be damaged, explode or
generate heat.
Only charge the battery at the specified vol-
■
tage. Never use a charging voltage other than
the specified voltage. Failure to comply could
result in burns or heat formation.
Do not use any transformers such as boosters,
■
motor generators or DC sources to charge the
battery. Failure to comply will result in a fault
or deep discharging of the charger.
Do not charge the battery in the rain or in lo-
■
cations where it might be exposed to spray or
moisture. If the battery is charged while wet,
electric shocks or short-circuiting is possible,
which could result in burning and a fire.
Do not touch the mains plug with wet hands. If
■
you touch it with wet hands, you could receive
an electric shock.
Do not cover the charger with a cloth or
■
similar. Application of a cover can generate
heat, resulting in deep-discharging or a fire.
Do not place the charger close to a fire or
■
naked flame.
Do not charge the battery in the vicinity of
■
combustible substances.
Charge the battery in a well ventilated
■
location and protect it against direct sunlight.
Charging in direct sunlight may overheat the
charger, which could result in deep-dischar-
ging or a fire.
Charge the battery in an ambient tempera-
■
ture range of 0°C to 40°C. If the ambient
temperature is below 0°C to 40°C, charging
may not be permissible because it could result
in a fire.
Do not allow any foreign bodies to get into
■
the ventilation openings or the battery contact
socket of the charger. Otherwise an electric
shock or other malfunctions could occur. Only
use the device in dust-free locations.
Safety instructions
Handle the mains cable with care. If you
■
carry the mains adapter using the mains
cable or pull it out of the mains socket via the
mains cable, the cable could be damaged
or cracked, which in turn could lead to a
short-circuit. Ensure that it does not come into
contact with cutting blades, hot substances, oil
or grease. Replace a damaged mains cable
with a new cable.
If the battery has been disconnected from
■
the tool housing, cover it with a sealing cap
until it is used again. To prevent short-circuits,
cover the terminal block (metal part) of the
unused battery with the cap provided with the
packaging.
Do not short-circuit the terminal block (metal
■
part) of the battery. If it is short-circuited, a
large current flows, overheating the battery,
which could result in burning or damage.
Do not throw the battery into the fire. Failure to
■
comply could result in an explosion.
When connecting the battery to the device,
■
observe the following to prevent malfunctions.
• Do not place your finger on the trigger.
• Do not press the workpiece contact against
• Keep your fingers or hand away from the
Be aware of changing noises or unusual
■
odours or noise. When the tool is activated
and then generates unusual odours or noise,
this is an indication of a fault. Use of the tool
in this condition can result in accidents. Con-
tact an authorised Würth dealer if anomalies
occur.
Disconnect the charger from the mains when it
■
is not being used.
the object.
nail outlet opening. Note whether there is
an operating noise when you connect the
battery.
— If you connect the battery and press the
workpiece contact against the floor or
similar, the tool fan runs, this is, however,
normal.
29