Bosch ANGLE EXACT ION 18 V-LI 8-1100 Manual Original página 19

OBJ_BUCH-1521-007.book Page 19 Friday, March 17, 2017 1:15 PM
– Pay attention not to damage the worklight cable and, with-
out kinking or bending it, slide it into the cavity 19 intend-
ed for it in the housing shell.
– Enclose the worklight 13 again with the two housing shells
of LED holder 12.
– Press the snap ring 18 and the marking ring 17 back to
their initial positions.
Mounting the Angled Screw Head (see figure D)
Applies for the ANGLE EXACT ION
following types: 8-1100 | 3-500 | 15-500 | 23-380 |
30-290
On these industrial cordless angle wrenches, a fitting angled
screw head (see "Angled drive head", page 17) has to be
mounted first.
– Hold the power tool with the open-end spanner 21 by the
spanner flats 4 of the angled head flange.
 Never clamp the tool by the housing shells!
– Mount the angled screw head 3 onto the flange in the re-
quested position and tighten the sleeve nut with the open-
end spanner 20 via the spanner flats 5.
Hold the angled head flange with the open-end spanner 21
to prevent turning.
Adjusting the Angled Drive Head
The angled drive head 3 can be adjusted to a total of eight po-
sitions.
– Hold the power tool with the open-end spanner 21 by the
spanner flats 4 of the angled head flange.
 Never clamp the tool by the housing shells!
– Loosen the sleeve nut with the open-end spanner 20 by
the spanner flats 5. Adjust the angled drive head 3 in 45°
steps to the desired position and retighten the sleeve nut
again with the open-end spanner 20 by the spanner flats 5.
Hold the angled head flange with the open-end spanner 21
to prevent turning.
Adjusting and Removing the Angled Drive Head
(see figure E)
Applies for the ANGLE EXACT ION
following types: 30-300 | 40-220 | 50-210 | 60-120
The angled drive head 3 with tool bit holder 2 can be continu-
ously adjusted around 360°.
– Loosen the lock nut 22 by inserting an appropriate tool in-
to an opening of the lock nut and turning the lock nut in the
direction of the arrow a (left thread).
– Fix the angled drive head 3 in this position by turning the
lock nut 22 in the direction of the arrow c against the an-
gled drive head. Tighten the lock nut 22 with a tightening
torque of max. 50 Nm again.
– Turn the angled drive head 3 in arrow direction b until the
desired work angle is reached, but not more than once by
360°.
The angled drive head 3 can also be removed completely,
e. g. when it is required to replace the marking ring 17 by one
with another colour or to adjust the worklight. Adjust the
worklight to the desired position first (see "Adjusting the
Worklight", page 18) before adjusting the angled drive head.
Bosch Power Tools
– Loosen the lock nut 22 by inserting an appropriate tool in-
to an opening of the lock nut and turning the lock nut in the
direction of the arrow a (left thread).
Unscrew the angled drive head 3 in arrow direction b until
it can be removed.
Unscrew the lock nut 22 from the motor housing 23 in ar-
row direction a.
Now, the marking ring can be exchanged or the worklight can
be adjusted.
– Turn the lock nut 22 in arrow direction c onto the motor
housing 23 and screw on the angled screw head again
turning in arrow direction b.
– Lock the angle nutrunner head by screwing the lock nut 22
in arrow direction c.
– Retighten lock nut 22 again with a tightening torque of ap-
prox. 50 Nm.
Configuring the Power Tool
With the BOSCH EXACT Configurator software, different pow-
er tool settings (e. g., speed, driving stages, repeat protec-
tion) can be configured. For this, the power tool must be con-
nected to a PC via the USB data port.
Note: Observe all safety warnings and instructions in the soft-
ware instruction manual.
Changing Application Tools on the Screw Head
with External Square Drive (see figure F)
Inserting
– Press in the pin on the drive square of the tool holder 2,
e. g. using a small screwdriver, and slide the tool bit 1 over
the drive square. Pay attention that the pin engages in the
recess of the tool bit.
Removing
– Press in the pin in the recess of the tool bit 1 and pull the
tool bit out of the tool holder 2.
Changing Application Tools on the Screw Head
with Internal Hexagon (see figure G)
Inserting
– Insert the tool bit 1 into the internal hex socket of the tool
holder 2 until it can be felt to engage.
Removing
– Pull the tool bit 1 off of the tool holder 2 with the aid of pli-
ers, if necessary.
Changing Application Tools on the Head with
Quick-change Chuck (see figure H)
Inserting
Use only insertion tools with fitting end pieces
(1/4" hexagonal).
– Pull the sleeve of quick-change chuck 24 to the front and
hold.
– Insert tool bit 1 into tool holder 2 and release the quick-
change chuck.
English | 19
1 609 92A 3U0 | (17.3.17)