Care And Maintenance - Laica HYDROSMART VENEZIA Instrucciones Y Garantía

EN VENEZIA tap filter
6) Proceed as follows to install the body of the filtering system with the adapter M:
- Remove the fastening ring from the body of the filtering system and take the adapter L with a diameter of Ø 21 mm,
plus the seal N, and assemble the three pieces as illustrated in figures 6A, 6B, 6C.
6A
- Loosen the fastening band with a flat head screwdriver and remove the two rubber seals inside the adapter M (fig.
7A, 7B).
7A
- Choose the best seal: only the one with the biggest diameter (Fig. 8A) or both with one inserted inside the other
(fig. 8C). Then, insert them in the adapter, pressing firmly and taking extra care over which way up they are inserted
(fig. 8D).
8A 8B
- Install the adapter M on the tap and tighten the fastening band using a flat
head screwdriver to secure it firmly to the tap (fig. 9A and B).
9A 9B
7) Remove the HYDROSMART™ filter from its bag and rinse it under running water. Now, attach the filter to the body
of the device as shown in figures 11A, 11B, 11C.
11A 11B
03
6B 6C
7B
8C 8D
- Screw the body of the filtering
system to the ring (fig. 10).
10
11C
03
12
Instructions and guarantee
ACTIVATING THE FILTER LIFE MANUAL INDICATOR
Turn the manual indicator of the filter life D to set the start
month of using the filter. The reference month must be
lined up with the O line.
SMART FILTRATION SYSTEM – FREE LAICA HOME
WELLNESS APP - USE
List of compatible devices:
• iOS: iPhone with version 10 operating system.
• For devices with Android™ operating system: from
version 6.0 (Marshmallow).
By adding the HYDROSMART™ filter to the free "Laica
Home Wellness" app, you can receive automatic notification
on your smartphone when to replace the filter.
1. Install the free "Laica Home Wellness" app on your
smartphone.
2. Start the app and enter the "FILTER" section from the
main screen.
3. Add the HYDROSMART™ FILTER by pressing the
"+" key. It is possible to add the filter by scanning
the QR code printed on the upper part of the filter or
manually by pressing the "Select manually" button.4.
The app adds the filter and automatically prompts the
replacement date. To optimise the effective duration of
the filter based on the water treated, you can select the
chlorine level in your water supply. To use it properly,
request further information from your water supplier or
carry out a preliminary assessment of the local water
supply.
5. Save the settings by pressing the key.
6. When the filter replacement date is reached, the
notification to replace it will appear on your smartphone.
The notification is also sent to the email address given
during registration.
• To scan the QR code on the upper part of the filter, you
must authorise the app to access to your smartphone
camera.
• To receive notifications when to replace the filter, you
must enable the settings on your smartphone.
• To replace the filter, you can add a new one by scanning
the QR code printed on the upper part of the filter or
by updating the expiry date by clicking on the "Filter
expired" button (click to replace)".
USING THE FILTERING SYSTEM
Activating the Laica HYDROSMART™ filter:
When first used and every time the HYDROSMART™
filter is changed, turn the tap on and allow the water to
flow through the filter for several minutes (at least 4-5
minutes) to correctly activate the materials of which the
filter is composed.
This water can be used for watering plants. If the Laica
filtering system has not been used for 24 hours or more,
allow the water to flow for 30-60 seconds before using
the filtered water again.
CAUTION:
- To guarantee the performance characteristics of the
filtering system, it is recommended to filter cold water
only.
- The flow of water at a temperature higher than 50°C
through the device may cause permanent damage. The
flow of water at a temperature higher than 35°C through
the filter may cause permanent damage.
- To adjust the water flow properly, open the tap slowly.
The Laica filtering system has 3 different ways of
dispensing the water which can be selected with the
selector C:
1) Filtered water for
drinking, washing
fruit and vegetables,
cooking and carry out
all routine tasks with
safe, pleasant tasting
water.
2) Unfiltered water with
spray head.
3) Unfiltered water with
continuous stream.
REPLACING THE FILTER
To replace the filter, turn the filter anticlockwise and
remove it by pulling it outwards (fig. 12A, 12B, 12C).
12A 12B
12C
03
Replace it with a new filter repeating the steps described
in point 7 of the paragraph "PREPARING THE FILTERING
SYSTEM", "ACTIVATING THE FILTER LIFE MANUAL
INDICATOR" and "USING THE FILTERING SYSTEM -
Activating the Laica HYDROSMART™ filter".
To achieve the best results and guarantee the safety of
the filtering system, we recommend replacing the filter
every 3 months or 900 litres of filtered water.

CARE AND MAINTENANCE

Make sure your hands are clean during maintenance work
on the filtering system.
Periodically clean the outer part of the filtering system
with a damp sponge and a mild detergent, and rinse
thoroughly with cold drinking water. Do not use aggressive
13
EN
03