General Safety Information; Work Area Safety; Electrical Safety; Personal Safety - RIDGID 600 Manual Del Usuario

No. 600 Portable Power Drive

General Safety Information

W ! R
ARNING EAD AND UNDERSTAND ALL INSTRUCTIONS
F
AILURE TO FOLLOW ALL INSTRUCTIONS LISTED
BELOW MAY RESULT IN ELECTRIC SHOCK
/
AND OR SERIOUS PERSONAL INJURY
SAVE THESE INSTRUCTIONS!

Work Area Safety

1. Keep work area clean and well lit. Cluttered
benches and dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flam-
mable liquids, gases, or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep by-standers, children, and visitors
away while operating a power tool. Dis-
tractions can cause you to lose control.
4. Do not let visitors contact the tool or exten-
sion cord. Such preventative measures reduce
the risk of injury.

Electrical Safety

1. Double Insulated tools are equipped with a
polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in
any way. Double Insulation eliminates the need
for the three wire grounded power cord and
grounded supply system.
2. Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electrical
shock if your body is grounded.
3. Don't expose power tools to rain or wet con-
ditions. Water entering a power tool will
increase the risk of electrical shock.
4. Do not abuse cord. Never use the cord to
carry tools or pull plug from an outlet. Keep
cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords
immediately. Damaged cords increase the risk
of electrical shock.
5. When operating a power tool outside, use an
outdoor extension cord marked "W-A" or "W".
2
.
, ,
FIRE
.
Ridge Tool Company • Elyria, Ohio, U.S.A.
These cords are rated for outdoor use and
reduce the risk of electrical shock.
6. Connect the tool to an AC power supply that
matches the name plate specification. Incorrect
voltage supply can cause electrical shock or burns.
7. Inspect extension cord periodically and
replace if damaged. Do not let visitors con-
tact tool or extension cord. Damaged cords
increase risk of electrical shock

Personal Safety

1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use tool while tired or under the influ-
ence of drugs, alcohol, or medications. A
moment of inattention while operating power
tools may result in serious personal injury.
2. Dress properly. Do not wear loose clothing
or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving
parts. Loose clothes, jewelry, or long hair can
be caught in moving parts.
3. Avoid accidental starting. Be sure switch is
OFF before plugging in. Carrying tools with
your finger on the switch or plugging in tools that
have the switch ON invites accidents.
4. Remove adjusting keys or switches before
turning the tool ON. A wrench or a key that is
left attached to a rotating part of the tool may
result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. Proper footing and bal-
ance enables better control of the tool in unex-
pected situations.
6. Use safety equipment. Always wear eye pro-
tection. Dust mask, non-skid safety shoes, hard
hat, or hearing protection must be used for
appropriate conditions.

Tool Use and Care

1. Use clamp or other practical way to secure
and support the workpiece to a stable plat-
form. Holding the work by hand or against your
body is unstable and may lead to loss of control.
2. Do not force tool. Use the correct tool for
your application. The correct tool will do the
job better and safer at the rate for which it is
designed.