YATO YT-82822 Manual Original página 17

GB
emitting smoke or a strange smell. If you notice any deviations from the correct operation, you should turn off the tool, disconnect
the battery and pass the electric tool to the authorized repair service.
The tool is stopped after releasing the pressure on the switch. After switching of, the saw blade can move for some time.
The speed of the saw blade can be adjusted by the degree of the switch pressure, the greater the pressure on the on/off switch,
the greater the speed of the saw blade.
The tool is equipped with the lamp, which is illuminating the workplace. The light turns on automatically when the power tool is
started and turns off automatically when the power tool is turned off .
Cutting in a straight line.
Before you start cutting it is recommended that you mark the cut line, for example by using a pencil. You should also make sure
that the cut material does not contain items of diff erent hardness. For example, cut the wood should not contain nails, staples and
other metal items. You should also avoid the electrical wires, that may be hidden in the cut material.
Rest the tool base front on the cut material so the saw blade is not touching it.
Turn on the tool and let the saw blade achieve full adjusted speed.
Start cutting by leading the jigsaw with your both hands. During cutting you should press the saw to the surface and, at the same
time, by a smooth motion lead it along the cutting line. Use the minimum pressure which allows for the correct operation. Avoid
tilting the jigsaw, hitting by the blade in the crossing material and changes in direction of the cut. Failure to follow these instruc-
tions may lead to jamming of the saw blade in the cut material, damage or destruction (cracks) blade or cut material, as well as
to damage of the jigsaw itself.
During cutting a hard metal, for example a steel, your should use frequent breaks to cool the saw blade.
Cutting the curved line
You should comply with all the recommendations as in the case of cutting in a straight line, but you should use the saw blades
which are designed to cut arcs. They have a narrower blade than the saw blades designed for straight cutting and they make it
easier to cut arcs.
In the case of cutting holes, you should mark the shape of the cut hole, and then, at its edge, drill a hole with a diameter larger
than the width of the cutting blade. Drilled hole wall should be touching the line of the marked hole, which will be cut. In the hole
you should insert the saw blade of the jig saw and start cutting.
Additional notes
Do not allow to overload the tool, its external surfaces temperature should never exceed 60 C.
O
At the end of work you should turn off the tool, disconnect the battery, then make maintenance and inspection.
The declared, total declared value of vibration was measured by the standard test method, and it can be applied to compare one
tool to another. The declared total value of vibration can was used in a preliminary assessment of exposure.
Attention! The vibration emissions when working with the tool can diff er from the declared value, depending on how you use the
tool.
Attention! You should specify the security measures to protect the operator, which are based on an assessment of exposure in
the actual conditions of operation (including in it all parts of the work cycle, such as, for example, the time when the tool is turned
off or it is idling, and its activation time).
MAINTENANCE AND OVERHAUL
ATTENTION! Before any adjustment, technical service or maintenance operations unplug the tool. Once the operations have been
fi nished, the technical conditions of the tool must be assessed by means of external evaluation and inspection of the following
elements: body and handle, conductor with a plug and defl ection, functioning of the electric switch, patency of ventilation slots,
sparking of brushes, noise level of functioning of bearings and gears, start-up and smoothness of operation. During the guarantee
period, the user cannot dismantle the electric tools or change any sub-assemblies or elements, since it will cancel any guarantee
rights. All irregularities detected at overhaul or during functioning of the tools are a signal to have the tool repaired at a service
shop. Once the functioning has been concluded, the casing, ventilation slots, switches, additional handle and protections must be
cleansed with a stream of air (at a pressure not exceeding 0.3 MPa), with a brush or a cloth without any chemical substances or
cleaning liquids. Tools and handles must be cleansed with a clean cloth.
O R I G I N A L I N S T R U C T I O N S
17