Multiple Descaling System; Anti-Drip System - Bosch SensorSteam TDS12 Serie Instrucciones De Uso

Vertical steaming
This can be used to remove creases from
hanging clothes, curtains etc. It cannot be used
on a synthetic setting for delicate items.
Warning!
Do not iron clothing while it is being worn!
Never spray or aim the steam at persons or
animals!
• Set the temperature control (14) to the "•••" or "max"
position and the steam control to the
• Hold the iron in an upright position about 15 cm
away from the garment being steamed.
• The shot of steam button (5) on the handle may
be additionally pressed at intervals of 5 seconds.
However, after 4 shots of steam, wait for 10 seconds
to allow for continued steam production.

Multiple descaling system

Depending on the model, this range of irons is
equipped with the following de-scaling features
"AntiCalc".
f
1. self-clean
The self-clean filter between the water tank and the
pump prevents scale impairing the steam generation
system and ensures the optimum production of
steam.
2. anti-calc
The "anti-calc" cartridge has been designed to
r
reduce the build-up of scale produced during steam
ironing, helping to extend the useful life of your iron.
Nevertheless the "anti-calc" cartridge cannot prevent
all of the scale that is produced naturally over time.
3. calc'n clean
r
The "calc'n clean" function helps to remove scale
particles out of the steam chamber. Use this function
approximately every 2 weeks, if the water in your
area is very hard.
Follow the procedure described below:
a) Remove the plug from the socket, ensure that the
iron has cooled down and that the water tank (10)
is empty.
b) Set the temperature control (14) to the "calc'n
clean" setting.
c) Fill the water tank (10) to the maximum level with
clean tap water.
d) Plug in the iron and select the maximum steam
setting "max" by pressing the steam selection
button (3).
All manuals and user guides at all-guides.com
(8) e) Hold the iron over a sink or a container to collect
f) Grip the handle (1) until the water tank (10) is
g) Repeat the procedure until particles no longer
h) Turn the temperature control (14) to the maximum
i) Clean the soleplate (12) of the iron.
position.
4. calc'n clean with descaling fluid
(model dependent)
For deep descaling, use the descaling fluid (16)
supplied.
This should be carried out every 3 months.
The descaling fluid (16) can be obtained from our
After-sales service or.
(9)
Follow the procedure described below:
a) Remove the plug from the socket, ensure that the
b) Set the temperature control (14) to the "calc'n
c) Fill the water tank (10) with tap water mixed with a
d) Plug in the iron and select the maximum steam
e) Hold the iron over a sink or a container to collect
f) Grip the handle (1) until the water tank (10) is
g) Then follow the procedure described above in

Anti-drip system

If the temperature control (14) is set too low (below
"••"), the steam is automatically switched off to
prevent water from dripping out of the soleplate (12).
The "ActiveControlAdvanced" indicator lamp (2) on
the handle flashes and the pump will not work.
the water.
empty. This could take several minutes.
come out of the soleplate (12) of the iron.
setting. The iron will begin to emit steam. Wait until
the water inside the iron has evaporated.
Accessory code Name of accessory
(After-sales)
311144
iron has cooled down and that the water tank (10)
is empty.
clean" setting.
measure (25 ml) of the descaling fluid (16).
setting "max" by pressing the steam selection
button (3).
the water.
empty.This could take several minutes.
section "3. calc'n clean" until particles no longer
come out of the soleplate (12) of the iron.
en
(E-shop)
TDZ1101
13