Description Of Symbols - Silverline 972660 Manual

GB
Introduction
Thank you for purchasing this Silverline product. This manual contains information necessary
for safe and effective operation of this product. This product has unique features and, even
if you are familiar with similar products, it is necessary to read this manual carefully to
ensure you fully understand the instruction. Ensure all users of the product read and fully
understand this manual.

Description of Symbols

The rating plate on your tool may show symbols. These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction manual.
Caution!
DO NOT use in rain or damp environments!
For indoors use only!
Be aware of kickback!
Class I construction (double insulated for additional protection)
Dust extraction required or recommended
Always disconnect from the power supply when adjusting, changing accessories,
cleaning, carrying out maintenance and when not in use!
Environmental Protection
Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your local authority or retailer for recycling
advice.
Conforms to relevant legislation and safety standards.
8
Original Instructions
Technical Abbreviations Key
V Volts
~, a.c. Alternating current
A, mA Ampere, milli-Amp
n No load speed
0
° Degrees
Ø Diameter
Hz Hertz
W, kW Watt, kilowatt
min or min Operations per minute
-1
rpm Revolutions per minute
dB(A) Decibel sound level (A weighted)
m/s Metres per second squared (vibration magnitude)
2
Specification
Voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V~, 50Hz
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350W
Duty Cycle: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S2 30 minutes (short time duty)
No load speed – Sanding disc (n ):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1450/min
0
Sanding disc size:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø150mm
Belt size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .914 x 100mm & 915 x 100mm
Belt table tilt angle: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0° - 90°
Belt surface area: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 x 100mm
Table size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 x 125mm
Belt speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292m/min / 4.87m/s
Belt Sander Dust Port: . . . . . . . . . . . . . . . . Ø 40mm (external), Ø 37mm (internal)
Sanding Disc Dust Port: . . . . . . . . . . . . . . . Ø 40mm (external), Ø 34mm (internal)
Table tilt: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-45°
Protection class: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ingress protection: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IP20
Power cord length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2m
Dimensions (L x W x H):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520 x 380 x 315mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.6kg
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
Sound and vibration information:
Sound pressure L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 dB(A)
PA
Sound power L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 dB(A)
WA
Uncertainty K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3dB
Vibration:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<2.5 m/s
The sound intensity level for the operator may exceed
85dB(A) and sound protection measure are necessary.
WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and limit the
time of exposure if necessary. If sound levels are uncomfortable, even with ear protection, stop
using the tool immediately and check the ear protection is correctly fitted and provides the correct
level of sound attenuation for the level of sound produced by your tool.
WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness,
tingling and reduced ability to grip. Long-term exposure can lead to a chronic condition. If necessary,
limit the length of time exposed to vibration and use anti-vibration gloves. Do not operate the tool
with hands below a normal comfortable temperature, as vibration will have a greater effect. Use the
figures provided in the specification relating to vibration to calculate the duration and frequency
of operating the tool.
Sound and vibration levels in the specification are determined according to international standards.
The figures represent normal use for the tool in normal working conditions. A poorly maintained,
incorrectly assembled, or misused tool, may produce increased levels of noise and vibration.
www.osha.europa.eu provides information on sound and vibration levels in the workplace that
may be useful to domestic users who use tools for long periods of time.
2