Connecting Other Equipment; Precautions Before Making Connections; Connecting With Ios Devices; Adjusting The Input Sound - Tascam 102i Serie Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 31

Connecting other equipment

This is an example of SERIES 102i connections.

Precautions before making connections

0 Carefully read the operation manuals of the devices to be con-
nected and then connect them correctly.
0 Before making connections, turn this unit and all equipment to
be connected off (standby).
0 If possible, install all connected devices so that they are pow-
ered from the same AC power supply line. When using a power
strip or similar device, be sure to use one that has a thick cable
with high current capacity in order to minimize voltage fluctu-
ations in the AC power supply.
Mic
Examples of connections to a SERIES 102i (front)
Mic preamp with S/MUX
(When using the OPTICAL OUT (S/MUX) of a TASCAM SE-
RIES 8p Dyna as the clock master for this unit)
Powered speakers
Examples of connections to a SERIES 102i (back)
V CAUTION
MONITOR
PHONES
Set the
and
before changing the input switch setting. Failure to do so could
cause sudden loud noises from monitoring equipment, and this
could damage equipment or harm hearing.
ATTENTION
i Input switches can be set for each channel separately. Do not
+48V
set the switch to
when connecting a mic that does not re-
quire phantom power.
i Do not connect or disconnect mics when the switch is set to
+48V
. Doing so could cause a loud noise and might damage this
unit and connected equipment.
+48V
i Set the switch to
only when using a condenser micro-
Headphones
Guitars
Drum machine
Computer
knobs to their minimum values
phone that requires phantom power. Setting the switch to +48V
when a dynamic mic or other device that does not require it is
connected could damage this unit and connected equipment.
i When using condenser mics that require phantom power and
dynamic mics together, be sure to use balanced dynamic mics.
Unbalanced dynamic mics cannot be used when phantom
power is enabled.
i Supplying phantom power to some ribbon mics could break them.
If you are unsure, do not supply phantom power to a ribbon mic.

Connecting with iOS devices

You can use a Lightning to USB Camera Adapter* to connect the
unit to an iOS device and use it as an interface with that device.
* You must obtain a genuine Apple Lightning to USB Camera
Adapter separately.
NOTE
When connected, this unit will not provide power to the iOS
device.

Adjusting the input sound

Analog audio signals input into this device from mics, guitars, key-
boards and other audio equipment can be converted into digital
signals and transmitted to the computer via USB. You can use the
features of this unit to adjust the digital signals that are sent to the
computer. In addition, by connecting speakers (through an ampli-
fier if not powered) or headphones to this unit, you can monitor
audio signals that are input to this unit and output from the com-
puter.
Use the various controls on the front of the unit as necessary while
listening to the input sound.
SERIES 102i
SERIES 208i
GAIN
Adjust the
knobs (4) to adjust the analog input levels of the
1-2
3-4
input jacks (1) or
input jacks (2, SERIES 208i only) so that
PEAK
the
indicators (3) above and to the right of the knobs do
not light.
To listen to the monitoring signal using headphones, connect
PHONES
headphones to the
PHONES
knob (6).
NOTE
Check the following if you cannot hear the input sounds.
PHONES
i Use the
knob on the front panel to adjust the out-
PHONES
put levels of the
MONITOR
i Use the
knob on the front of the unit to adjust the
LINE OUT (BALANCED) 1-2
output levels of the
TASCAM SERIES 102i / SERIES 208i
or
jack (5) and then adjust the
and
jacks.
jacks.
11

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

208i serie

Tabla de contenido