Functional Description - Stanley LH187C Manual De Instrucciones

This manual is consistent with the date of manufacture of
your machine, you will find information on the technical data
of the machine acquired manual check for updates of our
machines on the website: www.grupostayer.com
The machine is intended for dry sanding and polishing of
wood, plastic, metal, filler, as well as for painted surfaces.
It is especially suitable for profiles, corners or hard to reach
locations. Please refer to the booklet included in delivery for
the safety instructions.
MACHINE-SPECIFIC SAFETY WARNINGS
Use the machine only for dry sanding. Penetration of water
into the machine increases the risk of an electric shock.
Caution, fire hazard! Avoid overheating the object being
sanded as well as the sander. Always empty the dust
collector before taking breaks.
In unfavourable conditions, e. g., when sparks emit from
sanding metals, sanding debris in the dust bag, micro filter or
paper sack (or in the filter sack or filter of the vacuum cleaner)
can self-ignite. Particularly when mixed with remainders of
varnish, polyurethane or other chemical materials and when
the sanding debris is hot after long periods of working.
- Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
- Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn
or explode.
- Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug
when the cable is damaged while working. Damaged
cables increase the risk of an electric shock.
BATTERIES USE AND CARE
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery, vapours
may be emitted. Provide for fresh air and seek medical help
in case of complaints. The vapours can irritate the respiratory
system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery against
dangerous overload.
Use only original STAYER batteries with the voltage listed
on the nameplate of your power tool. When using other
batteries, e. g. imitations, reconditioned batteries or other
brands, there is danger of injury as well as property damage
through exploding batteries.
Do not continue to press the On/Off switch after the machine
has been automatically switched off. The battery can be
damaged.
The battery is equipped with a temperature control which
allows charging only within a temperature range of between
0 °C and 45 °C. A long battery service life is achieved in this
manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories page.
Only these battery chargers are matched to the lithium ion
battery of your power tool.
ENGLISH
13
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable
battery temperature range of 0–50 °C is exceeded, the
speed is reduced. The power tool will not run at full speed
until reaching the allowable battery temperature. position.
Unintentional actuation of the On/Off switch can lead to
injuries.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool. Firmly tighten
the collar of the keyless chuck 2 by hand in rotation direction
. This automatically locks the drill chuck.
The locking is released again to remove the tool when the
collar is turned in the opposite direction.

FUNCTIONAL DESCRIPTION

Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Please read the operating instructions carefully before
assembling and using.
ASSEMBLY
Fitting the dust bag (Fig. 2)
Fit the dust bag 6, in the vacuum intake 9.
Important! For health safety reasons it is imperative that
you use a dust bag.
Assembly the dust collector box (LH190E fig.5)
Place the dust box 6 in the vacuum intake 9.
- Making the notches fit into the hopper 6.
- Proceed to rotate in clockwise direction, until it locks.
- To remove the hopper 6, rotate counterclockwise and pull
out.
Fastening the sanding/grinding paper (Fig. 4-6-7-8).
First disconnect the power plug.
- Release the latches 8 on both sides.
- Place the abrasive sanding/grinding sheet outward the
sanding plate.
- Place the sanding/grinding sheet edge on the top of the
sanding plate 7 and fasten the front retainer 8 (LH190E).
- Attach sheet sanding/grinding to sanding plate 7. Sure
it is taut.
- Finish attaching the sanding/grinding sheet to the back
retainer 8. (Fig. 4, 7-8).
- Make sure the holes in the sanding/grinding sheet match
the sanding plate 7 for a perfect vacuum.
13