Flex SMS 190 18.0-EC Manual De Instrucciones página 32

Adjusting (see figure K2):
– Adjust by tightening or loosening the bevel-
stop bolt (33) on the tool with a 5mm hex
wrench (not included).
– Retighten the bevel-lock knob and push the
bevel-stop lever (11) in.
In case the bevel indicator (10) is not in a
line with the 45° mark of the scale (9), firstly
check the 0° setting for the bevel angle and
the angle indicator again. Then repeat the
adjustment of the 45° bevel angle.
Adjusting Mitre-Angle
The use of mitre-control lever (see
figure L)
The mitre-control lever can be positioned in
three positions. If take the horizontal position
as a start point, lift it to get upper position.
Press it down to get lower position.
Horizontal position
– For the most commonly used angle
0°,15°,22.5°,31.6°, and 45° right/left mitre
angle ,the mitre- detent pin (L-1) can be fully
engaged into the notch on the mitre scale.
– For other angle, the mitre – detent pin will
override the mitre detents.
Upper position (also known as unlocked
position)
– The mitre-detent pin doesn't work anymore,
at this moment the mitre table can rotate
freely.
Lower position (also known as locked
position)
– The mitre table should be secured in place.
Adjusting the mitre-table to the most
commonly used angle
– Adjust the mitre-control lever to the upper
position and hold it in place, move the mitre
table close to the desired most commonly
used angle.
– Release the mitre-control lever, it will go back
to horizontal position automatically. Hold
the mitre-control lever continue to rotate
the mitre table toward the desired angle,
until the mitre-detent pin is snapped into the
detent.
– Press down the mitre-control lever to secure
the mitre table in place.
Adjusting the mitre-table to other angle
The mitre angle can be set in the range from
32
48° (left side) to 48° (right side).
– Adjust the mitre-control lever to the upper
position and hold it in place, move the mitre
table close to the desired angle.
– Press down the mitre-control lever to secure
the mitre table in place.
Adjusting Bevel Angles (see
figure M)
NOTE
This mitre saw can be tilted to left or right
side. In general, the adjusting method are the
same, except the bevel-stop lever (11) need
to be rotated to let the saw head go to the
right side.
Here raise the right bevel as an example:
– Loosen the bevel-lock knob (34).
– Rotate the bevel-stop lever, and place it in
rest position.
– Hold the saw arm and tilt to the desired
bevel angle.
– Tighten the bevel-lock knob.
NOTE
The bevel angle of this saw can be set range
from 48° (left side) to 48° (right side). To get the
angle more than 45°, just simply turn the 45°
stop block (32) completely to the front of the
saw.
Adjusting the tightness of
Mitre-control Lever (see figure N)
NOTE
This adjustment was made at the factory
and, under normal circumstances, it does not
require re-adjustment.
To adjust
– Raise the saw arm by releasing the arm-lock
pin.
– Lift the mitre-control lever.
– Remove the three screws (N-1) securing the
insert plate (N-2) with the supplied double-
ended allen wrench, and remove the plate and
set aside.
– Locate the lock nut (N-3).
– Using a Φ3mm pin, insert into the hole in the
lock nut, adjust by tightening or loosening
the lock nut until the proper amount of
tension in the mitre-control lever is attained.
– Reinstall the insert plate.
– Press the mitre-control lever down to lock
the mitre table in place.
SMS 190 18.0-EC