Basic Cleaning - Black and Decker BXCO850E Manual De Instrucciones

ENGLISH
the pump.
♦ Close The steam knob (R) by turning, clockwise.
Obtaining steam:
♦ The steam is used to foam milk for cappuccino, and also
to heat other liquids.
♦ Turn the appliance on using the on/off button.
♦ The indicators of 1cup coffee button, 2cup coffee button
and steam button flash, the machine begins preheating,
after all indicators are solidly on, the right temperature
is reached.
♦ For Steam, press the Steam heating button (H), with
Steam icon flashing, and continue heating until the
steam temperature has been reached.
♦ The Steam light will illuminate steady, indicating that
the water has reached the necessary temperature for
generating steam.
♦ Note: During operation, the indicator in the steam
selector will cycle on and off to maintain to desired
temperature.
♦ Place a recipient under the steam tube.
♦ Open Steam knob (R) anticlockwise
♦ Steam only will begin to exit.
♦ When you have enough, close the steam knob (R) by
turning clockwise and remove the recipient.
IMPORTANT
♦ When you finish doing steam, you must replace the
water used to make steam and at the same time, recover
the temperature (lower) to make coffee.
♦ To do this, with the steam knob open, pushing previously
over Steam Icon to stop heating, push coffee / water
button (G1 or G2), which will activate the pump.
♦ Put a container under the tube
♦ When water starts to flow through the steam pipe, it
means that it has recovered the coffee temperature and
the boiler has been filled. Now you can close Steam
knob and to push coffee button (G) to Stop position
Autooff feature:
♦ The BLACK+DECKER machines are designed to save
energy
To that end, after some minutes from the last operation,
the unit switches to energy saving mode
To return to normal operation you should just Switch ON
the connect button (F)
6
(Original instructions)
Once you have finished using the appli-
ance:
♦ Turn the appliance off, using the on/off switch (F) for a
few seconds
♦ Unplug the appliance to the mains.
♦ Remove the water from the water tank.
♦ Clean the appliance
CLEANING

Basic cleaning

♦ Disconnect the appliance from the mains and let it cool
before undertaking any cleaning task.
♦ Clean the equipment with a damp cloth with a few drops
of washingup liquid and then dry.
♦ Do not use solvents, or products with an acid or base pH
such as bleach, or abrasive products, for cleaning the
appliance.
♦ Do not let water or any other liquid get into the air vents
to avoid damage to the inner parts of the appliance.
♦ No parts of this appliance are suitable for cleaning in the
dishwasher.
♦ After washing, dry all the parts before fitting them
together and storing.
Cleaning the Frothing Wand
♦ CAUTION! The frothing wand, and frothing sleeve may
be VERY HOT.
♦ It is recommended to purge and wipe the frothing wand
after steaming milk to prevent deposits of dirt and before
turning off the machine.
♦ To do this, pull the frothing sleeve down and clean under
warm running water.
♦ Fill a cup with a bit of water, immerse the frothing wand
into the water.
♦ Drain hot water through the pipe, following the instruc-
tions "Obtaining hot water".
♦ Use a cloth to dry the frothing wand and replace the
frothing sleeve.
♦ In case no steam comes out of the frothing wand,
hardened milk blocks its path. Carefully use a needle to
loosen the milk residue from the opening of the frothing
tip to remove any blockage,
♦ Once clean, rinse with running water from the tap and
reassemble it. Then steam again.