Protecting The Environment - Black and Decker KW750 Traducido De Las Instrucciones Originales

English
(original instructions)
Planing
● Hold the tool with the nose piece of the shoe resting on
top of the workpiece surface.
● Switch the tool on.
● Move the tool steadily forward to perform the
cutting stroke.
● Switch the tool off after the stroke has been completed.
Rebating (Fig. F)
● Fit and adjust the parallel fence.
● Proceed as for planing.
Chamfering edges (Fig. G)
The V-groove in the nose piece of the shoe enables you to
chamfer edges at 45°, 30° and 15° angles.
● Hold the tool at an angle with the desired groove (20)
around the edge of the workpiece and perform the
cutting stroke.
Parking rest (Fig. H)
Your planer is equipped with a parking rest (21) that
automatically lowers into place when the tool is lifted from the
work surface. When planing, the parking foot raises as the
tool is pushed forward. When the parking foot is lowered, the
planer can set on the work surface without the blade touching.
Hints for optimum use
● Move the tool along the grain of the wood.
● If the grain is cross or curly, or if the workpiece material is
a hard type of wood, adjust the depth of cut to take only a
very thin shaving at each pass and take several passes to
achieve the desired result.
● To keep the tool in a straight line, press down the front of
the tool at the start, and press down the back of the tool at
the end of the cutting stroke.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
The following types of cutting blades can be obtained from
your local retailer:
- Tungsten carbide tipped reversible cutting blades (part
no. X35007, supplied per pair)
- High-speed steel reversible cutting blades (part no.
X24192-XJ11, supplied per pair)
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
@
care and regular cleaning.
Warning! Before performing any maintenance on
the tool, unplug the tool. Unplug the charger before
cleaning it.
● Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
8
● Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Replacing the drive belt (Fig. I)
● Loosen the screws (15) and remove the cover (16).
● Remove the old drive belt.
● Place the new belt (17) over the pulleys. Place the
belt over the large pulley (18) first, then over the small
pulley (19), whilst manually rotating the belt steadily.
● Put the cover back in place and tighten the screws.
Motor brush inspection and replacement (Fig. J)
Brushes should be regularly inspected for wear.
● Remove brush cap (22). The brushes should slide freely
in brush box. If brushes are worn down to .3" (8 mm) they
should be replaced.
To reinstall, push new brush back into brush box. If replacing
existing brush, maintain same orientation as when removed.
Replace the brush cap (do not overtighten).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
● Safely dispose of the old plug.
● Connect the brown lead to the live terminal in the
new plug.
@
● Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth
terminal. Follow the fitting instructions supplied with
good quality plugs. Recommended fuse: 5 A.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com