Black and Decker KA274EKA Traducido De Las Instrucciones Originales página 26

EnGLIsH
Sander Operation (Fig. E)

WARNING: Let the tool work at its own pace. Do
not overload.
NOTICE: This sander is not to be used in
drywall applications.
To operate your sander, grasp it as shown in Figure E and turn it
on. Move it in long, sweeping strokes along the surface being
sanded, letting the sander do the work. Pushing down on the
tool while sanding actually slows the removal rate and produces
an inferior quality surface. Be sure to check your work often, this
sander is capable of removing material rapidly, especially with
coarse paper.
Your sander is designed to sand flush on three sides for sanding
in corners, and its small size and light weight make it ideal for
overhead work.

WARNING: Use extra caution when working overhead
and always wear approved eye protection.
The orbital action of your sander allows you to sand with the
grain or at any angle across it for most sanding jobs. On the final
sanding steps, as discussed below, a better finish will result if
you sand only with the grain.
To produce the best finish possible, start with coarse grit abrasive
paper and change gradually to finer and finer paper. A final sanding
with a piece of well‑worn fine abrasive paper will produce a
professional‑looking finish that in many cases will need no hand
sanding at all. The rate at which the dust collection bag will fill up
will vary with the type of material being sanded and the coarseness
of the abrasive paper. For best results, empty the bag frequently and
check the opening for clogging.
When sanding painted surfaces, you may find that the abrasive
paper loads up and clogs with paint. A heat gun will work much
better to remove paint before sanding. FOLLOW ALL SAFETY
INSTRUCTIONS IN HEAT GUN INSTRUCTION MANUAL.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
C
Lubrication
Your power tool requires no additional lubrication.
24
D
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered by
BLACK+DECKER, have not been tested with this product,
use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only BLACK+DECKER
recommended accessories should be used with
this product.
Consult your dealer for further information on the
appropriate accessories.
Storage
• Switch off the tool
• Always store your products disconnected from power supply!
• Store the tool in a place that is as cool and dry as possible.
• Store the tool in a place where they cannot be accessed by
children or unauthorised persons.
• Do not place the power tool with the grinding head down
- always place it on the floor so that it is on its side with
the brush ring facing down. Otherwise the sanding pad
could deform.
• Check the tool for damage before use after long periods
of storage.
Transport

CAUTION: Accidental starting during transport!
• Always transport your products disconnected from
power supply!
• Check the tool for damage before use after transport.
Protecting the Environment
Separate collection. Products marked with this
w
symbol must not be disposed of with normal
household waste.
Products contain materials that can be recovered
or recycled reducing the demand for raw materials. Please
recycle electrical products according to local provisions. Further
information is available at www.2helpU.com.