Starting Procedure; Searching By Pty Information; Storing The Strongest Broadcast Frequencies; Displaying The "Radio Settings" Screen - Pioneer MVH-AV285BT Manual De Instrucciones

Radio
p By keeping pressing and holding
perform non stop seek tuning. If you press again, non stop
seek tuning is cancelled and the preset channel is switched.

Starting procedure

1 Press .
2 Touch [Radio].
The "Radio" screen appears.

Searching by PTY information

You can tune into a station using PTY (Programme Type
Identification) information.
1 Touch .
2 Touch or to select the item.
The following items are available:
News&Info (default), Popular, Classics, Others.
3 Touch to start searching.
 If you touch [Cancel], the searching process is
cancelled.
Storing the strongest broadcast
frequencies
The BSM (best stations memory) function automatically stores
the six strongest broadcast frequencies under the preset tuning
keys "1" to "6".
p Storing broadcast frequencies with BSM may replace those
you have already saved.
p Previously stored broadcast frequencies may remain stored
if the number of frequencies stored has not reached the
limit.
1 Touch .
2 Touch to begin a search.
While the message is displayed, the six strongest broadcast
frequencies will be stored under the preset tuning keys in order
of their signal strength.
 If you touch [Cancel], the storage process is
cancelled.
12
Displaying the "Radio settings"
or , you can
screen
1 Press .
2 Touch
3 Touch [AV Source Settings].
4 Touch [Radio settings].

Tuning into strong frequencies

p You can use this function when "Radio" is selected as the
source.
Local seek tuning allows you to only tune into those radio sta-
tions with sufficiently strong signals.
1 Display the "Radio settings" screen.
 Displaying the "Radio settings" screen on page 12
2 Touch [Local].
3 Touch the item you want to set.
 Off (default):
Turns the seek tuning setting off.

Level1 to Level4:
Sets the level of sensitivity for FM to Level1 to Level4 (for
AM Level1 or Level2).
p The FM "Level4" (AM "Level2") setting allows reception of
only stations with the strongest signals.
Setting the FM or AM tuning
step
You can switch the tuning step for FM or AM band.
p For FM band, the seek tuning step is fixed to 50 kHz.
p The tuning step remains at 50 kHz during manual tuning.
1 Turn the source off.
 Selecting a source on page 7
2 Display the "Radio settings" screen.
 Displaying the "Radio settings" screen on page 12
3 Touch [FM Step] or [AM Step] to switch the
tuning step.
The following items are available for each setting:
FM Step
 100kHz(default)
 50kHz
, and then .
AM Step

9kHz (default)

10kHz
Setting the alternative fre-
quency search
When the tuner cannot get a good reception, tunes to another
broadcast station that supports the same programme in the
current network.
1 Display the "Radio settings" screen.
 Displaying the "Radio settings" screen on page 12
2 Touch [Alternative FREQ] to switch "On" or
"Off" (default).

Setting the Auto PI search

When you switch to the broadcast station containing RDS data,
searches for the same PI (Programme Identification) code broad-
cast station from all frequency band automatically.
1 Turn the source off.
 Selecting a source on page 7
2 Display the "Radio settings" screen.
 Displaying the "Radio settings" screen on page 12
3 Touch [Auto PI] to switch "On" or "Off"
(default).
p Even if you set to "Off", the PI search is automatically per-
formed when the tuner cannot get a good reception.
Limiting stations to regional
programming
You can switch whether the area code is checked during the
auto PI search.
1 Display the "Radio settings" screen.
 Displaying the "Radio settings" screen on page 12
2 Touch [Regional] to switch "On" (default) or
"Off".