Tabla de contenido
Publicidad
Warning Atención Attention
EN
Read entire booklet carefully before begin-
ning installation and save these instructions.
Please contact our technical department with
any queries.
Always take into account all the specifications
of the appliance that figure on the grey label
stuck to the lamp and on the installation dia-
gram.
To avoid damage to finish, assemble motor on
soft padded surface or use the original foam
inset in motor box. Do not lay fan on its side as
this could result in shifting of motor in decora-
tive enclosure.
To reduce the risk of personal injury, attach
the fan directly to the support structure of the
building according to these instructions, and
use only the hardware supplied.
To avoid possible electrical shock, before in-
stalling your fan, disconnect the power by turn-
ing off the circuit breakers to the outlet box and
associated wall switch location.
For the electrical connection it is necessary to
incorporate an isolator switch according to the
installation regulations, which ensures all-pole
cut, directly connected to the power terminals
and it must have a contact separation in all its
poles, which provides total disconnection under
category III surge conditions.
All wiring and connections must be made in
accordance with national and local electrical
codes.The ceiling fan must be earthed in order
to prevent possible electric shock. If you are not
familiar with the way to do the electrical instal-
lation, you must use the services of a qualified
electrician.
Ensure that you don´t drill through electrical
wires or any other obstruction in the wall or
ceiling during installation. Electrical wiring may
never be clamped or twisted between the ceil-
ing fan support and the mounting surface.
Make sure that the fan is disconnected from the
mains before removing the protection.
To reduce the risk of personal injury, do not
bend the blade attachment the system when
installing, balancing or cleaning the fan. Nev-
er insert foreign objects between rotating fan
blades.
To reduce the risk of fire, electrical shock or
motor damage, do not lift or carry the fan by
the lead wires.
ATTENTION: If you notice an unusual oscillat-
ing movement of the fan, stop the fan immedi-
ately and contact the manufacturer, your ser-
vice agent or suitably qualified persons.
The assembly and replacement of the safe-
ty suspension system must be carried out by
the manufacturer, its agent or suitably qualified
persons.
The roof fixing system must support at least 4
times the weight of the fan.
The fan blades cannot be installed lower than
2,3m from the floor.
Do not install the ceiling fan on surfaces that
are moist, dreshly painted or electrically con-
ductive.
All ceiling fans without special protection
against dust or moisture (no IP rating) may be
used indoors, except in bathrooms.
The lights with LED modules should be posi-
tioned in such a way that they are not exposed
to direct sunlight or other sources of heat.
The important precautions, safeguards and
instructions appearing in this manual are not
meant to cover all possible conditions and sit-
uations that may occur. It must be understood
that common sense, caution and carefulness
are factors which cannot be built into this prod-
uct. These factors must be supplied by the per-
son(s) installing, caring for and operating the
unit.
Our fans comply with current safety regulations.
The internal or external manipulation of the
ceiling fan may reduce its safety. The manufac-
ture cannot be held liable for any manipulation
carried out by the user.
As our products are subject to technical mod-
ifications, we cannot guarantee, that all infor-
mation is always up to date. Please contact our
technical department with any queries.
Important
Nominal voltage (V) Difference of electrical po-
tential (voltage) between two points. This volt-
age must not exceed that marked on the fan.
Nominal frequency (Hz) Measures the number
of repetitions per unit of time (Hertz). This fre-
quency must not exceed the one marked on the
fan.
Current intensity (A-Ampere) is the flow of elec-
trical charge that travels through a material.
Nominal power (W) the maximum power that
the fan demands at different speeds, under nor-
mal conditions of use.
Number of turns (RPM) Of the fan depending
on the selected speed.
Publicidad
Tabla de contenido
