Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
6. Make sure that the Heat Gun has cooled completely
before storing it away.
Failure to observe this may result in burns or
malformation of the storage case.
7. Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your
eye will be hurt.
SPECIFIC SAFETY RULES AND SYMBOLS
1. NEVER operate from an unstable footing, such
as when on a ladder or step ladder.
Doing so may cause an injury.
2. Before operation, remove any objects in the area
that may cause injury or accident.
3. Precautions during transport
• Turn off the switch on the body of the machine
and remove the battery.
• Carry the machine by the handle on its body.
• When transporting it via vehicle, take appropriate
steps to prevent it from falling over or being
damaged.
4. NEVER use a Heat gun for applications other
than those specifi ed.
NEVER use a Heat gun for applications other than
those specifi ed in the Instruction Manual.
5. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
6. Do not use Heat gun if the plastic housing or
handle is cracked.
Cracks in the Heat gun's housing or handle can lead
to electric shock. Such Heat gun should not be used
until repaired.
7. NEVER use a Heat gun which is defective or
operating abnormally.
If the Heat gun appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange for
repairs by a metabo HPT authorized service center.
8. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened
with soapy water and dry thoroughly.
9. Defi nitions for symbols used on this tool
V ............ volts
— --- ......... direct current
10. Do not use the product if the tool or the battery
terminals (battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
6
11. Keep the tool's terminals (battery mount) free of swarf
and dust.
○ Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
○ During use, try to avoid swarf or dust on the tool from
falling on the battery.
○ When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result
in smoke emission or ignition.
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of battery chargers.
To avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1.
This manual contains important safety and operating
instructions for battery charger Model UC18YFSL.
2.
Before using battery charger, read all instructions and
cautionary markings on (1) battery charger, (2) battery,
and (3) product using battery.
3.
To reduce risk of injury, charge metabo HPT
rechargeable battery models of the multi volt series
and the BSL18 series. Other models of batteries may
burst causing personal injury and damage.
4.
Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fi re, electric shock, or injury to persons.
5.
To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
6.
Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress.
7.
An extension cord should not be used unless
absolutely necessary. Use of improper extension cord
could result in a risk of fi re and electric shock.
If extension cord must be used make sure:
a.
That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b.
That extension cord is properly wired and in good
electrical condition; and
c.
That wire size is large enough for AC ampere
rating of battery charger as specifi ed in Table 1.
Publicidad
Tabla de contenido
