Operation - tormatic HA MS 400V Manual De Instrucciones Y De Montaje

Menu 9 Service menu
menu Entry Selection
item
90 Selection of the door maintenance cycle
0 No service interval (default setting)
1 1000 cycles
2 4000 cycles
3 8000 cycles
4 12000 cycles
5 16000 cycles
6 20000 cycles
7 25000 cycles
8 30000 cycles
9 35000 cycles
10 40000 cycles
11 45000 cycles
12 50000 cycles
91 Cycle counter output door cycles
92 Selection of the loading bridge maintenance cycle
0 500 cycles
1 1000 cycles
2 1500 cycles
3 2000 cycles
4 2500 cycles
5 3000 cycles
6 3500 cycles
7 4000 cycles
8 4500 cycles
9 5000 cycles (default setting)
10 5500 cycles
11 6000 cycles
93 Cycle counter outputloading bridge cycles
94 Preselection of the door sealing maintenance cycle
0 500 cycles
1 1000 cycles
2 1500 cycles
3 2000 cycles
4 25000 cycles
5 3000 cycles
6 3500 cycles
7 4000 cycles
8 4500 cycles
9 5000 cycles (default setting)
10 5500 cycles
11 6000 cycles
95 Cycle counter output door sealing cycles
96 Operating hours counter output – hours
97 Error memory output hours – error code
98 Software version output – serial number – creation
date
99 Reset to default setting
Press for 5 s
- - Exit menu
7

Operation

Safety instructions for operation
Observe the following safety information for operation:
• The operator must be instructed on how to handle the
control or the controlled loading bridge and be familiar with
the applicable safety regulations.
• Comply with the accident prevention regulations and
general safety regulations relevant to the field of application.
• Check the control and the controlled loading bridge for
visual defects before use.
• If you detect any safety-relevant deficiencies, decommission
the loading bridge and report all defects to the responsible
line manager.
• Have the deficiencies remedied immediately.
• If the operational behaviour of the loading bridge changes,
switch the system off immediately. Recommissioning must
be prevented. Notify the operating company of the change.
Crush hazard by moving loading bridge
WARNING
Limb crush hazard when moving loading bridge.
•
•
Tripping or falling hazard when loading!
CAUTION
With the control switched off, triggered emer-
gency stop switch or active restart lock, the float-
ing position of the loading bridge is not active
and the vertical movements of the truck are not
balanced out.
•
Commissioning of the loading bridge
1. Switch the main switch to the "I" (On) position.
2. Briefly actuate the
Functional description for the loading bridge operation
Lifting
Hold the button: the loading bridge is lifted. The support is
swivelled out simultaneously in the upper working area of the
loading bridge. After letting go of the
is lowered automatically.
Floating position
After letting go of the lifting
lowered onto the truck with the support and is in floating position.
The loading bridge follows the vertical movements of the truck.
Restart lock
After switching the main switch or emergency stop switch back
on, the restart lock is active. The yellow warning indicator flashes
in the display.
Tripping or falling hazard when loading!
CAUTION
With the control switched off, triggered emer-
gency stop switch or active restart lock, the float-
ing position of the loading bridge is not active
and the vertical movements of the truck are not
balanced out.
•
In order to deactivate the restart lock, briefly actuate the
ton.
HA MS 400V / 230V
The loading bridge must be visible from the
place of operation.
During lifting and lowering the loading
bridge, it is not permitted to persons to be in
the travel path of the loading bridge.
It is not permitted to drive on the loading
bridge until restart.
button.
button, the loading bridge
button, the loading bridge is
It is not permitted to drive on the loading
bridge until restart.
but-
EN - 17