Black and Decker CS2000 Manual De Instrucciones página 19

c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by Black &
Decker, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following
symbols:
Hz ....... Hertz
Read
Instructions
W ........ Watts
Manual
min ..... minutes
Use Eye
Protection
..... Alternating
Current
Use Ear
Protection
..... Direct
Current
V ........ Volts
n ....... No-Load
0
Speed
A ........ Amperes
All manuals and user guides at all-guides.com
FEATURES (Fig. A)
1. Lock Chain
2. Spark deflector screw
3. Spark deflector
4. Base
5. Fence
6. Vise
7. Flat Wrench
8. Crank
9. Vise Lever
10. Wheel
11. Guard
12. Spindle Lock
13. Depth Stop Bolt and Jam Nut
14. Trigger Switch
15. Padlock Hole
16. Fence Bolts
f Always wear proper eye and respiratory
f Before using, inspect the cutting wheel for cracks
f When starting the tool with a new or replacement
f In operation, avoid bouncing the wheel or giving it
f Clean your chop saw periodically following the
f Do not remove wheel guards or base.
f ALWAYS USE THE VISE OR SPECIAL FIXTURE TO
...... Class II
Construction
.... Earthing
Terminal
f Use only 14" type 1 wheels rated at 4300 rpm or
.... Safety Alert
Symbol
f Allow cut off parts to cool before handling.
.../min.. Revolutions
or Recipro-
f Do not attempt to cut wood or plastic with this tool.
cation per
minute
f NEVER CUT MAGNESIUM WITH THIS TOOL.
f Use chop saw in a well-ventilated area.
f Turn chop saw off before removing any pieces from
ENGLISH • 19
ADDITIONAL SAFETY RULES
FOR CHOP SAWS
protection.
or flaws. If such a crack or flaw is evident, discard
the wheel. The wheel should also be inspected
whenever you think the tool may have been
dropped. Flaws may cause wheel breakage.
wheel or if you are unsure of the condition of the
wheel, hold the tool in a well protected area and
let it run for one minute. If the wheel has an
undetected crack or flaw, it should burst in less than
one minute. Never start the tool with a person in line
with the wheel. This includes the operator.
rough treatment. If this occurs, stop the tool and
inspect the wheel for cracks or flaws.
procedure in this manual.
CLAMP WORK SECURELY. Other aids such as
spring, bar, or C-clamps may be appropriate for
certain sizes and shapes of workpiece. Use care in
selecting and placing these clamps and make a dry
run before making a cut.
higher.
the base.