Cutting Capacity; Standard Equipment - Black and Decker CS2000 Manual De Instrucciones

20 • ENGLISH
f DO NOT CUT ELECTRICALLY LIVE MATERIAL.
f Do not use circular saw blades or any other
toothed blades with this tool. Serious injury may
result.
f DO NOT OPERATE THIS TOOL NEAR
FLAMMABLE LIQUIDS, GASES OR DUST. Sparks
or hot chips from cutting or arcing motor brushes may
ignite combustible materials.
f Do not use the side of the abrasive wheel as a
deburring grinder. This will substantially weaken the
wheel creating an unsafe condition. The wheel may
come apart.
Caution! Wear appropriate hearing protection
during use. Under some conditions and duration of
use, noise from this product may contribute to hearing
loss.
Caution! Spark deflector will get hot. Avoid touching or
adjusting while hot. Keep cordset and materials away from
spark deflector.
• Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay on the
skin may promote absorption of harmful chemicals.
Warning! Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust
exposure.
Direct particles away from face and body.
For your convenience and safety, the following
warnings are on your Heavy-Duty 14" (355mm) Chop
Saw:
FOR SAFE OPERATION READ THE INSTRUCTION
MANUAL.
f Do not use toothed blades.
f Use only reinforced wheels rated 4300 rpm or
higher.
f When servicing use only identical replacement
parts.
f Always: wear eye protection, use guards, clamp
work in vise, use proper respiratory protection.
f Do not expose to rain or use in damp locations.
f Only use chop saw wheel of a max. Thickness of
2.8Mm and a max. Diameter of 355mm.
POWER SUPPLY
Be sure your power supply agrees with the nameplate
marking. A voltage decrease of more than 10% will
cause a loss of power and overheating.
All manuals and user guides at all-guides.com

CUTTING CAPACITY

The wide vise opening and high pivot point provide cutting
capacity for many large pieces. Use the cutting capacity
chart to determine total maximum size of cuts that can be
made with a new wheel.
shaped objects may require
Additional holding means if they cannot be held
securely in vise.
MAXIMUM CUTTING CAPACITY
Workpiece
Shape

STANDARD EQUIPMENT

1 14" Metal Cutting Abrasive Wheel
1 Wheel Wrench
1 Instruction manual
TO CARRY (FIG. A)
Fold down unit to position where you can carry the saw.
Hook lock chain (1) to lock arm down.
UNLOCKING (FIG. A)
To unlock tool and raise head, depress motor arm slightly
and unhook lock chain (1) out. Motor arm will then pivot
upward.
Caution! Certain large, circular or irregularly
Caution! Do not cut magnesium with this tool.
Note: Capacity shown on chart assumes no wheel
wear and optimum fence position.
90° Cutting
Angle
A = 4-7/8"
(125mm)
A = 4-1/2"
(115mm)
4-1/2" x 5-1/8"
(115mm x
130mm)
4" x 7-5/8"
A x B
(102mm x
188mm)
3" x 7-3/8"
(76mm x
229mm)
A = 4-1/2" x
5-3/8"
(115mm x
137mm)
45° Cutting
Angle
A= 4-1/2"
(115mm)
A = 3-13/16"
(98mm)
4-1/2" x 3-13/16"
4-1/8" x 3-3/4"
(105mm x
95mm)
A = 3-13/16"
3-3/4"
(95mm)