Troubleshooting - Sears Kenmore 665.72002 Manual De Uso Y Cuidado

TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the
cost of an unnecessary service call.
Nothing will operate
• Is the power outlet properly wired and polarized?
Try another outlet to check for proper wiring and polarity.
Is the power supply cord unplugged?
Plug into a properly grounded 3 prong outlet.
Has a household fuse been blown or has the circuit
breaker been tripped?
Replace the fuse or reset the circuit.
Is the main or regulator gas shutoff valve in the off
position?
See Installation Instructions.
• Is the range properly connected to the gas supply?
Contact a Sears trained repair specialist or see Installation
Instructions.
Surface burners will not operate
• Is this the first time the surface burners have been used?
Turn on any one of the surface burner knobs to release air
from the gas lines.
• On some models, is the Oooktop Lockout set?
See "Cooktop Lockout" section.
• Is the control knob set correctly?
Push in knob before turning to a setting.
• Are the burner ports clogged?
See "Sealed Surface Burners" section.
Surface burner flames are uneven, yellow and/or noisy
• Are the burner ports clogged?
See "Sealed Surface Burners" section.
• Are the burner caps positioned properly?
See "Sealed Surface Burners" section.
Is the burner damaged?
On models with caps, look for a warped cap. If cap will spin
freely on a flat surface, painted side down, the cap is warped.
Switch cap with a different surface burner to check for further
warping. Contact a Sears trained repair specialist. See back
cover.
Is propane gas being used?
The appliance may have been converted improperly.
Contact a Sears trained repair specialist. See back cover.
Surface burner makes popping noises
• Isthe burner wet?
Let it dry.
Excessive heat around cookware on cooktop
• Is the cookware the proper size?
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than 1 in. (2.5 cm) outside the cooking area.
Oven will not operate
• is the power outlet properly wired and polarized?
Try another outlet to check for proper wiring and polarity.
• Is this the first time the oven has been used?
Turn any one of the surface burner knobs on to release air
from the gas lines.
• Is the electronic oven control set correctly?
See "Electronic Oven Control" section.
• On some models, is the Oven Lockout set?
See "Oven Lockout" section.
Oven burner fails to light
• A household fuse has blown or a circuit breaker has been
tripped.
• The ignition system is broken. Contact a Sears trained repair
technician. See back cover.
Oven makes muffled ticking noise when in use
• This is normal and occurs when the oven burner cycles on
and off to hold the set oven temperature.
Oven burner lights, then goes out after I minute
• Press OFF/CANCEL, then wait 1 minute before trying again.
• is the power outlet properly wired and polarized?
Try another outlet to check for proper wiring and polarity.
Oven burner flames are yellow or noisy
• Is propane gas being used?
The appliance may have been converted improperly. Contact
a Sears trained repair specialist. See back cover.
Oven temperature too high or too low
• Does the oven temperature calibration need adjustment?
See "Oven Temperature Control" section.
Display shows messages
• Is the display showing "PF"?
There has been a power failure. Press OFF/CANCEL to clear
the display. Reset the clock, if needed. See "Clock" section.
On some models, is the display showing a "PF" and a
cooktop icon?
The Cooktop Lockout feature is engaged. See "Cooktop
Lockout" section.
Is the display showing "F" followed by a number?.
Press OFF/CANCEL to clear the display. If an "F" code
reappears, contact a Sears trained repair specialist. See
back cover.
Is the display showing a "EO F5"?
The Self-Cleaning latch is interferring with the oven door
closing. Press OFF/CANCEL to clear display. Depress and
hold door switch plunger (located on the oven front frame).
Latch mechanism will unlock after 6 seconds.
24