Casals SA650PEL Manual De Instrucciones página 6

- Loosen the set off screws (H) using the Allen wrench (I)
- Slide the shoe (D) all the way back.
Curved cuts:
For sawing on a curve, use the special "curved cut" blade,
which is thin enough to saw along a curve.
Perforating wood (Fig 5):
To perforate wood, there are two possibilities:
1- Drill a hole and begin sawing from that point.
- Place the jig-saw on the rounded edge located at the
front of the bottom plate.
- Turn on the saw and slowly lower it until it touches the
material to be sawed.
- Once the material has been perorated, return the saw to
its normal position and continue sawing.
- Plunge cuts may only be applied to soft materials, such
as wood, gypsum board, etc. For plunge cuts, use only
short saw blades.
Dust extraction Assembly
- Connect dust extraction adaptor (K) on the appliance
- Connect the vacuum aspirator suction tube to the dust
extraction adaptor (K)
- Stop the appliance by releasing the on/off switch .
Cleaning
- Disconnect the appliance from the mains and allow it to
cool before undertaking any cleaning task.
- Clean the electrical equipment and the mains connection
with a damp cloth and dry. DO NOT IMMERSE IN WATER
OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a few drops
of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning the
appliance.
- Do not let water or any other liquid get into the air vents
to avoid damage to the inner parts of the appliance.
- Never submerge the appliance in water or any other
liquid or place it under running water.
- If the appliance is not in good condition of cleanliness, its
surface may degrade and inexorably affect the duration
of the appliance's useful life and could become unsafe
to use.
6
Supplies Supplies
your appliance model. your appliance model.
- These supplies are available in specialist shops. - These supplies are available in specialist s
Anomalies and repair
- Take the appliance to an authorised technical support - Take the appliance to an authorised tech
service if a product damage or other problems arise. Do service if a product damage or other proble
not try to dismantle or repair without assistance, as this not try to dismantle or repair without assis
may be dangerous. may be dangerous.
- If the connection to the mains has been damaged, it - If the connection to the mains has been
must be replaced and you should proceed as you would must be replaced and you should proceed
in the case of damage. in the case of damage.
Specifications: Specifications:
- Rated Power: - Rated Power:
- Rated Voltage: - Rated Voltage:
- No load Speed - No load Speed
- Wood cutting capacity - Wood cutting capacity
- Steel cutting capacity - Steel cutting capacity
- Aluminium cutting capacity - Aluminium cutting capacity
- slant up to - slant up to
- Weight: - Weight:
- Sound Pressure level - Sound Pressure level
- Sound Power level - Sound Power level
- Instantaneous sound pressure level - Instantaneous sound pressure level
- Vibration - Vibration
notice of purpose of improvement. notice of purpose of improvement.
-Measured sound level determined according EN60745 -Measured sound level determined accordin
-The vibration emission level given in this information -The vibration emission level given in this inf
sheet has been measured according EN60745 and may sheet has been measured according EN607
be used to compare one tool with other. It may be used be used to compare one tool with other. It m
for a preliminary assessment of exposure for a preliminary assessment of exposure
-The vibration value during actual use of the power tool -The vibration value during actual use of the
can differ from the declared total value depending on the can differ from the declared total value depe
way in which tool is used way in which tool is used
-It's necessary identify safety measures to protect the -It's necessary identify safety measures to p
operator that are based on an estimation of exposure in operator that are based on an estimation of
the actual conditions of use (taking account of all parts the actual conditions of use (taking account
of the operating cycle such as the times when the tool is of the operating cycle such as the times whe
switched off and when it is running idle in addition to the switched off and when it is running idle in ad
trigger time). trigger time).
For EU product versions and/or in case that it is re- For EU product versions and/or in case
quested in your country: quested in your country:
Anomalies and repair
SA650PEL
650W
230V~
0-2800 rpm
65 mm
6 mm
8 mm
45º
1.90 Kg
(LpA) = 83B(A), KpA = 3dB
(LwA) = 94dB(A), KWA = 3dB
(LpCpeak) = 96dB(C), KpCpeak = 3dB (LpCpeak) = 96dB(
6.38 m/s2, K=1.5 m/s2
(LpA) =
(LwA) = 9
6.3