Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGlIsh
Attaching Garden Hose (Fig. D)
NoTE: Before connecting the garden hose to the pressure
washer unit, run water through the garden hose for thirty
seconds to clear any debris from inside the garden hose.
1. To connect the garden hose to the pressure washer
unit
, screw the filter
8
2. Connect the garden hose to the hose connector
by loosening the screw of the garden connector and
attaching the hose onto the connector (for B2C, AR, B2
and BR executions). Connect the garden hose to the
hose connector
20
the garden connector (for B3 execution).
3. Attach the garden hose
connector to the filter
NoTE: Always disconnect the garden hose after usage.
Attaching Nozzles (Fig. E)
DANGER: Risk of fluid injection. Do not direct
discharge stream toward persons, unprotected skin,
eyes or any pets or animals. Serious injury will occur.
WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while
pressure washer is running. Turn pressure washer unit
OFF before changing nozzles.
1. To connect a nozzle to the spray wand
the nozzle button
3
appropriate nozzle.
2. Release the button to lock the nozzle in place.
3. Give the nozzle a firm tug to ensure the nozzle is
locked into place.
Spray Fan to Pencil Jet Nozzle
adjusting Fan pattern (Fig. E1)
The angle of spray coming out of the spray wand may be
adjusted by rotating the nozzle. This will vary the spray
pattern from approximately a 0 ° narrow high impact stream
to a 60 ° wide fan spray.
A wide fan pattern distributes the impact of the water over
a larger area, resulting in excellent cleaning action with a
reduced risk of surface damage. Large surface areas can be
cleaned more quickly using a wide fan pattern.
A narrow pencil jet stream distributes the impact of the water
in a concentrated area, resulting in a high impact force on
the cleaning surface. Use a narrow pencil jet stream for deep
cleaning in a concentrated area. However, use it cautiously, as
it may damage some surfaces
Attaching Soap Bottle (Fig. J4)
To connect the soap bottle
the end of the soap bottle inside the spray handle and turn
the soap bottle counterclockwise to lock it into position.
NoTE: The wand and soap bottle cannot be installed at the
same time.
NoTE: The soap bottle should be positioned underneath the
barrel of the spray handle. Do not position the soap bottle
above the barrel of the plastic gun as this will lead to soap
dripping on the barrel.
26
to the water intake
21
by screwing the garden hose to
mounted onto the garden
26
until it "clicks".
21
, depress
2
on the spray wand and insert the
16
to the spray handle
Spray Tip
Spray fan to pencil jet nozzle
Turbo Nozzle
OPERATION
.
12
WARNING: To reduce the risk of serious personal
20
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the spray handle
grip
and the other hand on the spray handle
5
Pressure Washing
Preparing Surface for Cleaning
•
Remove objects from the area which could create a
hazard such as children's toys or outdoor furniture.
•
Insure that all doors and windows are closed tight.
•
Protect all plants and trees in the adjacent area with a
drop cloth ensuring that they will not be harmed by
any overspray.
•
Pre‑rinse cleaning area with fresh water.
•
Use only detergents formulated for pressure washers.
•
Always test detergent in an inconspicuous area
before use.
Preparing Pressure Washer Unit for Use
(K1, K2, K3, K4)
DANGER: Risk of fluid injection and laceration.
When using the high-pressure setting, DO NOT allow
the high-pressure spray to come in contact with
unprotected skin, eyes, or with any pets or animals.
Serious injury will occur.
CAUTION: Before operation:
1. Connect the garden hose to a water supply. Water can
be drawn from a faucet or another water supply. Refer to
self priming under Preparing Pressure Washer Unit
for Use.
2. Connect the high pressure hose to the pressure washer
4
, insert
and the spray handle. For instructions on connecting
the high pressure hose to the pressure washer and spray
handle, please refer to attaching high pressure hose
under Assembly and Adjustments.
3. Connect the garden hose to the pressure washer. For
instructions on connecting the water supply to the
pressure washer, please refer to attaching Garden hose
under Assembly and Adjustments.
4. Plug the power cord into an appropriate power source.
Application
For gentle wide area cleaning.
For abrasive cleaning.
.
4
Publicidad
Tabla de contenido
