Technical Specifications - resideo Braukmann VWS01Y-11/4 Guia De Inicio Rapido

Ocultar thumbs

Contenido

página de 21

/ 21
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

Valve Open

1. Push the power button on L5 WiFi Water Leak Shutoff

Valve, or tap the open command in the app's menu.

2. The valve opening process is initiated. The status LED

is pulsing green.

3. The valve is open. The status LED is solid green.

EMERGENCY BALL VALVE CLOSE /

OPEN

The handle on the L5 actuator is intended to be used for

emergencies only. For example, during a power outage.

Please follow the steps below if you need to use the

emergency handle:

1. Unplug the L5 WiFi Water Leak Shutoff Valve from the

power supply.

2. Push on the lever until it touches the actuator's top

cover. You should feel minimum resistance. This step

is important to allow the handle to be detached from

the gearbox.

3. While pushing down the handle, turn the lever clock-

wise to close the ball valve. You may feel some resis-

tance just like when you are closing a regular ball valve.

4. To open the valve, push down the handle while turning

it counterclockwise. You may feel some resistance just

like when you are opening a regular brass ball valve.

IMPORTANT

Since the handle is intended to be used in emergen-

cies only, when using the emergency handle to close

the valve, the valve status change does not synchro-

nize with the app.

PAIR L5 WITH WATER SENSOR(S)

L5 works with both Resideo's new L1 and the original WiFi

Water Leak and Freeze Detector. The detector(s) and L5 need

to be set up in the same location in the app in order for the

devices to be paired with each other.

You can choose which specific detector(s) you want to

enable L5's automatic shutoff function. You can change the

setting at any time under "LEAK PROTECTION". This can be

found on the bottom of L5's home page in the app, or as a

first time user, you will be taken through the setup of this

function automatically.

Inch

Model

(mm)

VWS01Y-1/2 2.598

4.567

(66)

(116)

VWS01Y-3/4 2.953

4.567

(75)

(116)

VWS01Y-1

3.583

4.567

(91)

(116)

Table 3. Dimensions.

Inch

(mm)

2.677

3.976

3.228

4.606

(68)

(101)

(82)

(117)

2.677

4.252

3.228

4.685

(68)

(108)

(82)

(119)

2.677

4.409

3.228

5.000

(68)

(112)

(82)

(127)

MAINTENANCE CYCLE

This function can be found under "Settings" or you will

automatically be taken through the setup process as a first

time user. It's designed to close, then immediately open your

L5 valve regularly to prevent the valve gets stuck. We

recommend you set the maintenance cycle to take place at

least every 2 months.

IMPORTANT

— To prevent unintended water supply, the valve main-

tenance cycle will not perform when the valve is in

the closed position.

— If you are considering having the valve permanently

closed, manually open, then close the valve at least

every 2 months.

SYNCHRONIZE THE VALVE

POSITION WITH APP STATUS

If for any reason, the valve's position does not match the

valve's status in the app, take the following steps to

synchronize the valve with the app's status.

1. Unplug the actuator from the power supply.

2. Plug back in the power supply. Once the L5 Actuator is

powered back up, it will operate the valve to the last

known position. Wait a few minutes until the status

LED is either solid red or solid green.

3. Now you should be able to see the valve status in the

app is aligned with the actual valve status.