Shark AI 360 ROBOT RV2500SEU Manual De Instrucciones página 9

For full instruction booklet visit: sharkclean.eu/RV2500SEU-IB.
STEP 1
PREP THE ROBOT
.......... Side Brushes ..........
• Remove protective film from robot and base.
• Attach the side brushes to the posts on the bottom
of the robot.
STEP 3 CHARGING YOUR ROBOT
6
h
First
Charge
INDICATOR
• Place robot on base to charge for 6 hours.
• When the robot is properly aligned with its BACK
against the base, the Charging Icon on the top
right side of the base will illuminate and the
Battery icon on the robot will illuminate.
• Make sure the robot is properly aligned on the base.
• TO TURN ON ROBOT: Place robot on base or press
and hold the CLEAN button for 5 to 7 seconds
until the indicator lights turn on.
BASE INDICATOR LIGHTS
Dust Bin
Release Button
sha rkcl e a n.eu
SETUP
STEP 2 SET UP THE SELF-EMPTY BASE
1m
1m
1.5m
• Find a permanent location for the base in a central
area with a strong Wi-Fi signal.
• Remove any objects that are closer than 1m. from either
side of the base, or closer than 1.5m. from the front.
• Plug in the base. The Base Power Indicator Icon
on the top right side of the base will illuminate when
the basehas power. Make sure the power switch on
the back of the base is in the (I) ON position.
STEP 4
PREP YOUR HOME
• Before cleaning, clear cords and remove small
obstacles like clothing or toys that are less than
8cm tall.
• Open interior doors in rooms you want your robot
to clean.
Base Power Indicator Icon
Base is plugged in and has power.
Charging Icon
Robot is properly aligned on base and
charging.
Evacuation Icon
Robot is emptying debris into base.
CHECK BASE FILL LEVEL
Place base
on bare
The base is designed to hold weeks of debris. During
floor against
initial use, you may have to empty it more frequently
the wall.
while the robot finds more debris than usual. Check the
fill level regularly to know when to empty.
AVOID MOVING THE ROBOT OR BASE
While your robot is cleaning, DO NOT pick it up and
move it, or move the charging base—this will impact
the robot's ability to map your home.
NOTE: To order replacement parts and filters, visit: sharkclean.eu
Questions? Easy Steps If You're Stuck:
Having trouble connecting to your robot?
For how-to videos, FAQs, troubleshooting, and tips & tricks visit: sharkclean.eu.
For full instruction booklet visit: sharkclean.eu/RV2500SEU-IB.
ERROR
ERROR CODE
#
(RED) + (RED)
2
alternating or (WHITE) +
(RED) flashing
(RED) + (RED)
2
flashing
(RED) + (RED) +
2
(RED) flashing
6
(RED) flashing
(RED) + (WHITE)
7
flashing
10
(RED) flashing
LIVING WITH YOUR ROBOT
DOORWAYS AND THRESHOLDS
Your robot can easily climb over most thresholds, but
if any are higher than 2cm, set up a no-go zone in the
app to block them off.
CLEANING ROBOT'S FILTER
IMPORTANT - Clean filter every month or loss of
suction may occur.
!
Rinse and let air dry completely. Also, tap loose dirt
off filter between washes as needed.
Foam filter
Felt filter
Foam filters may appear dirty after use–this is normal.
DO NOT put your hands into any
opening not defined for user access
TROUBLESHOOTING
SOLUTION ERROR CODE
Blockage surrounding the
brushroll. Remove any debris from
around and inside the brushroll so
(RED) flashing
that it can spin freely.
Side brush is stuck. Remove
any debris from around the side
brushes so they move freely.
A drive wheel is stuck. Clean the
wheels and remove any debris
(RED) FLASHING +
wrapped around the axles so
(RED) solid
they can move freely.
Front bumper may be jammed.
Clean the bumper and make sure
it moves in and out freely.
To minimise the risk of the robot traveling beyond an unsafe boundary
Cliff sensor error. Move your
(stair/cliffs edges, fireplaces, water hazards), establish these areas as "no-go
robot to a new location and zones" using the mapping feature in the SharkClean mobile app. Upon setting
the boundary, run the vacuum and visually confirm that the settings effectively
clean its cliff sensors.
prevent the robot from passing beyond the set boundary.
Robot may be stuck on an
Adjust settings as necessary.
obstacle. Move robot to a new
DO NOT put hands into any opening in the dock or robot.
location on a level surface.
ERROR
SOLUTION
#
Battery is critically low and needs
recharging. Please pick up your
robot and place it on the base.
24 Make sure the charging indicator
on the top right side of the base is
illuminated to confirm your robot
is placed on the base correctly.
Blockage in dust bin. Check base
and robot dust bin for clogs. Clear
26 any debris and reinstall the dust
bin, ensuring that it clicks into
place.
WARNINGS
s ha rkc lea n.eu