Technical Specifications - Bestway Hydro-Force SUP Allround Board-Set HuaKa'i Manual De Instrucciones

EN
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS.
• Carefully read, understand, and follow all information in this user manual before inflating and using the SUP.
• These warnings, instructions, and safety guidelines address some common risks during the use of the SUP, but they cannot cover all risks and
dangers in all cases. For your own safety, always heed the advice and warnings in these instructions. Non-compliance with these operating
instructions may expose you to serious danger or death. Only use the product in the places and conditions for which it is intended.
• Safekeeping the instruction. If instruction is missing, search it in website www.bestwaycorp.com/support.
• Stand-up Paddling is a dangerous sport. Use of this product exposes the user to unexpected risks, dangers and hazards.
• User should realize and understand these risks. The use of this product implies the respect of the safety instructions described in the manual.
• Regardless of the number of persons on board, the total weight of persons and equipment must never exceed the maximum recommended load.
• Do not use this product if you are under the influence of alcohol, drugs or medications.
• Life saving devices such as life jackets and buoys should be pre-inspected and used at all times. Always paddle with an experienced partner when
using this product.
• Tell your sail routes and time schedule to your partner.
• Check the weather forecast first to know the marine environment and weather conditions before starting. Bad weather and marine environment is
very dangerous. Never use this product in conditions that are beyond your ability (such as, but not limited to, high surf, riptides, currents or river rapids)
• Use the product near the shore and beware of natural factors such as wind, tidewaters and tidal waves. BE AWARE OF OFFSHORE WINDS AND CURRENTS.
• Before every use, carefully inspect the product for signs of wear or leakage to ensure everything is in good condition. Please do not use the SUP if you find any damage. Do not surf in unfamiliar
water areas.
• Beware of potential harmful effects of liquids such as battery acid, oil and petrol. These liquids may damage the product. Inflate according to the rated pressure on the product or it will cause over
inflation and/or an explosion.
• Stay balanced. Uneven distribution of loads on the board may cause the board to overturn which could lead to drowning.
• Know how to operate this product. Check your local area for information and/or training as needed.
• Inform yourself about local regulations and dangers related to surfing, boating and/or other water activities.
• The air pressure gauge of the hand pump only shows the air pressure higher than 5 psi, which is normal. When the air pressure in the product is lower than 5 psi, the air pressure gauge will not
show a value.
• Extended exposure to sun can shorten the lifespan of your SUP. We suggest not leaving SUPs in direct sunlight for more than 1 hour after use.
• Store in a cool, dry place and out of children's reach.
• Do not unfold this product when the temperature is low. The product should be placed at room temperature (over 20˚C) for 24 hours before inflation. Deflate completely before folding the SUP.
• Take the SUP out from the bag and refer to the packaging steps for long-term storage.

TECHNICAL SPECIFICATIONS

Item Inflated Size
3.05m x 84cm x 15cm
65346
(10' x 33" x 6")
INSTALLATION OF THE SUP
For the installation instructions, read the drawings inside the manual. Drawings are for illustration purpose only. May not reflect actual product. Not to scale.
1. Open the inflation valve, push on the pin and rotate anticlockwise. (Fig 1).
2. Connect the inflation hose to the inflation valve (Fig 2).
3. Inflate the SUP to 1.03 bar (15 psi) (Fig 3).
4. Close the valve before use (Fig 4).
USAGE OF THE SUP
For the usage instructions, read the drawings inside the manual. Drawings are for illustration purpose only. May not reflect actual product. Not to scale.
1. Adjust the length of oar before using the SUP (Fig 1).
2. Kneel on the board (Fig 2).
3. Gradually stand up on one leg (Fig 3).
4. Stand up with the other leg and keep your hands on the board (Fig 4).
MAINTENANCE AND STORAGE OF THE SUP
For the maintenance and storage instructions, read the drawings inside the manual. Drawings are for illustration purpose only. May not reflect actual product. Not to scale.
1. Disassemble the fin (Fig 1).
2. Deflate the SUP by pushing on the pin and rotating clockwise. (Fig 2).
3. Fold the SUP, but not more than 10 cm every time (Fig 3).
REPAIR
For the repair instructions, read the drawings inside the manual. Drawings are for illustration purpose only. May not reflect actual product. Not to scale.
1. Deflate the board (Fig 1).
2. Clean around the surface around the leak (Fig 2).
3. Cut the repair patch to the suitable size (Fig 3).
Recommended Maximum Load
Working Pressure Capacity
130kg (287lbs)
1.03bar (15psi)
130kg
1.03 bar
15psi
Maximum Number
of Persons
1 Adult
0
1
5. Install the safety rope (Fig 5 & 6).
6. Install the fin (Fig 7).
7. Assemble the oar (Fig 8).
8. Completion (Fig 9).
5. Maintain balance with paddle (Fig 5).
6. Keep knees slightly bent, increase the balance buffer and start rowing (Fig 6).
7. Begin to row after standing up (Fig 7).
4. Pack the SUP (Fig 4).
5. Insert the SUP in bag (Fig 5).
4. Apply the glue and patch on the damaged surface (Fig 4).
5. Press the repair patch for 30 sec (Fig 5).
6. Wait 24 hours before use (Fig 6).
4
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals, Videos Or
Spare Parts, Please Visit
bestwaycorp.com/support