BFT GIOTTO BT A ULTRA 36 Instrucciones De Uso Y De Instalacion página 33

Logic Denition
Conguration of
EXPI1 input on
input-output expan-
EXPI1
sion board.
1-2
Conguration of
EXPI2 input
on input-output
EXPI2
expansion board.
1-3
Conguration of
EXPO2 output
on input-output
EXPO1
expansion board
4-5
Conguration of
EXPO2 output
on input-output
EXPO2
expansion board
6-7
TRAFFIC LIGHT Trac light
pre-ashing
PREFLASHING
TRAFFIC LIGHT
Steadily lit red light
RED LA P
ALWAYS ON
TABLE "C"  RADIO MENU RADIO
Logic Description
Add Start Key
Add start
associates the desired key with the Start command
Add 2ch Key
add 2ch
associates the desired key with the 2nd radio channel command.
Erase List
WARNING! Erases all memorized transmitters from the receiver's memory.
erase 64
Read receiver code
Displays receiver code required for cloning transmitters.
ON = Enables remote programming of cards via a previously memorized W LINK transmitter.
It remains enabled for 3 minutes from the time the W LINK transmitter is last pressed.
OFF= W LINK programming disabled.
ENGLISH
Cross out
Default setting
used
0 Input congured as Start E command.
1 Input congured as Start I command.
2 Input congured as Open command.
3 Input congured as Close command.
4 Input congured as Timer command
5 Input congured as Timer command.
6 Input congured as Timer Pedestrian command
7 Input congured as Phot (photocell) safety.
8 Input congured as Phot op safety (photocell active during opening only).
9 Input congured as Phot cl safety (photocell active during closing only).
1
10 Input congured as Bar safety (safety edge).
Input congured as Phot test safety (tested photocell).
11 Input 3 (EXPI2) on input/output expansion board is switched automatically to safety device test
input, EXPFAULT1.
Input congured as Phot op test safety (tested photocell active during opening only).
12 Input 3 (EXPI2) on input/output expansion board is switched automatically to safety device test
input, EXPFAULT1.
Input congured as Phot cl test safety (tested photocell active during closing only).
13 Input 3 (EXPI2) on input/output expansion board is switched automatically to
safety device test input, EXPFAULT1.
Input congured as Bar safety (tested safety edge).
14 Input 3 (EXPI2) on input/output expansion board is switched automatically to
safety device test input, EXPFAULT1.
0 Input congured as Start E command.
1 Input congured as Start I command.
2 Input congured as Open command.
3 Input congured as Close command.
4
Input congured as Timer command
5 Input congured as Timer command.
0
6
Input congured as Timer Pedestrian command
7 Input congured as Phot (photocell) safety.
8 Input congured as Phot op safety (photocell active during opening only).
9 Input congured as Phot cl safety (photocell active during closing only).
10 Input congured as Bar safety (safety edge).
0 Output congured as 2
1 Output congured as SCA (gate open light).
2 Output congured as Courtesy Light command.
11
3 Output congured as Zone Light command.
4 Output congured as Stair Light.
5 Output congured as Alarm.
6 Output congured as Flashing light.
7 Output congured as Latch.
8 Output congured as Magnetic lock.
11
9 Output congured as Maintenance.
10 Output congured as Flashing Light and Maintenance.
11 Output congured as Trac Light control with TLB board.
12 output congured as barrier status
0 Pre-ashing switched o.
0
1 Red lights ash, for 3 seconds, at start of operation.
0 Red lights o when gate closed.
0
1 Red lights on when gate closed.
Optional extras
Radio Channel.
nd
33
GIOTTO BT A ULTRA 36 -