DeWalt XR DCW220 Traducido De Las Instrucciones Originales página 37

Adjusting the Sanding Belt Tracking (Fig. C)

WARNING: Keep hands, fingers and loose clothing away
from moving belt.
Hold the tool firmly with one hand, start motor and observe
tracking of sanding belt. Use your other hand to adjust the belt
tracking adjustment knob 7
outward, turn the tracking adjustment knob counterclockwise
to make the belt run inward. If belt runs inward, turn the
tracking adjustment knob clockwise to make the belt
run outward.
Belt life will be greatly increased by keeping the tracking
adjustment set properly. To prevent the sanding belt from
rubbing against the sander housing, keep the edge of the belt
about 3 mm (7/64") to 5 mm (13/64") from the housing.
Changing The Sanding Belt (Fig. D, E)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: To reduce the risk of injury, make sure belt
is installed with arrows in proper direction of rotation.
Failure to do this could result in the belt unraveling
creating a hazardous condition.
Pull the quick release lever
tension on the sanding belt. Pull the sanding belt
two rollers. Put the new 75 mm x 533 mm (3" x 21") sanding
belt in position on the front and rear rollers (Figure E). Ensure
that the arrows on the sanding belt and on your belt sander are
pointing in the same direction. Use one hand to hold the unit
and use the other hand to push the lever to the rear to tension
the sanding belt.
Dust Extraction (Fig. F)

WARNING: Risk of dust inhalation. To reduce the risk of
personal injury, ALWAYS wear an approved dust mask.
A dust extraction port 8 is supplied with your tool.
The dust extraction port allows you to connect the tool to an
external dust extractor, either using the AirLock™ system, or a
standard 35 mm dust extractor fitment.

WARNING: ALWAYS use a vacuum extractor designed in
compliance with the applicable directives regarding dust
emission when sanding wood. Vacuum hoses of most
common vacuum cleaners will fit directly into the dust
extraction outlet.
Fitting and Removing the Dustbag (Fig. G)
• Fit the dustbag 17 over the dust extraction port
• To remove the dustbag, pull it off the dust extraction port.
Fitting and Removing the Swivel Dust
Adapter (Fig. H)
• Fit the swivel dust adapter
port . An external dust extractor, either using the AirLock™
8
to center the belt. If the belt runs
shown in Figure D to release the
4
1 from the
8
into the dust extraction
18
system, or a standard 35 mm dust extractor fitment can then
be attached to the swivel dust adapter.
• To remove the swivel dust adapter, pull it out of the dust
extraction port.
Wireless Tool Control (Fig. A)

CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with
the tool.
Your tool is equipped with a Wireless Tool Control transmitter
which allows your tool to be wirelessly paired with another
Wireless Tool Control device, such as a dust extractor.
To pair your tool using Wireless Tool Control, press and hold
the variable speed trigger
Control pairing button on the seperate device. An LED on the
seperate device will let you know when your tool has been
successfully paired.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. I)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main handle
and one hand on the auxiliary handle
Variable Speed Trigger and Lock‑On Button
(Fig. A)
To start your belt sander, depress the variable speed
trigger as shown in Figure A. To stop your belt sander release
2
the variable speed trigger. For continuous operation, depress
the variable speed trigger then depress the lock‑on button
and release the variable speed trigger. To stop your belt sander,
depress the variable speed trigger to release the lock‑on button.
Release the variable speed trigger.
Variable‑Speed Dial (Fig. J)
To operate the tool, select the speed setting you wish with the
.
speed dial 9 , shown in Figure J, and press the variable speed
trigger. The speed setting can be adjusted either with the tool
ON or OFF.
Be sure to select the proper speed for your sanding operation.
If in doubt about the proper speed for your operation, test the
performance at low speed settings and gradually increase until
a comfortable speed is found.
2 on the tool and the Wireless Tool
6 .
EnGLIsh
5
3
35